Domino

The DOMINO system is DUEMMEGI’s proprietary bus architecture for home automation. HSYCO fully integrates with this system through the DFCP control and gateway module, and its FXP-XT serial communication protocol.

A serial connection between the DFCP and the HSYCO SERVER is required for the integration, either directly through the server’s RS-232 port or via the RS-232 port of a supported serial to IP gateway, including the WEBS module.

Communication

Employ a DE-9 (often called DB-9) male-female RS-232 straight cable to connect the RS-232 DFCP port to the serial port on HSYCO SERVER or serial gateway.

RS-232 parameters:

Baud rate	9600, 38400, 57600 or 115200 bps (according to the DFCP serial port setting)
Data bits	8
Stop bit	1
Parity	none
Flow control	none

 A speed of 115200 bps is recommended to achieve good performance, particularly when the number of devices connected to the bus is large.

HSYCO Configuration

You can define and connect to more than one DOMINO bus using several DFCP gateways.

The DOMINO I/O Server also supports dual, redundant connections between HSYCO and DFCP.

If the main connection fails, HSYCO automatically re-routes the communication with DFCP through the fail-over connection.

Options

ID	Default	Values	Description
startupevents	false	true	generate IO events also during the driver’s start-up phase
		false	start generating events only after HSYCO is aligned with the current status of the system
inputdiscovery	false	true	auto-detects DOMINO’s input devices as configured in the DFCP, and automatically creates the list of all detected devices and individual data points in the systemtopo.txt file. Should be enabled to allow the automatic update of (button) objects’ states
		false	auto-detect for input devices is disabled
outputdiscovery	true	true	auto-detects DOMINO’s output devices as configured in the DFCP, and automatically creates the list of all detected devices and individual data points in the systemtopo.txt file. Should be enabled to allow the automatic update of (button) objects’ states
		false	auto-detect for output devices is disabled
virtualdiscovery	false	true	auto-detects DOMINO’s virtual points for input and output devices as configured in the DFCP, and automatically creates the list of all detected virtual data points in the systemtopo.txt file. Should be enabled to allow the automatic update of (button) objects’ states
		false	auto-detect for devices’ virtual data points is disabled
virtualpoints	false	1...2033	enables polling for the first n virtual points of the DFCP. Enable this option only if you need to generate I/O events based on these virtual points
		true	enables polling for all the 2032 virtual points of the DFCP
		false	polling of the DFCP virtual data points is disabled
registers	false	1...1024	enables polling for registers R0-Rn of the DFCP. Enable this option only if you need to generate I/O events based on these registers
		true	enables polling for registers R0-R127 of the DFCP
		false	polling of the DFCP registers is disabled
powerdisplay	false	true	enables polling for registers R0-Rn of the DFCP. Enable this option only if you need to generate I/O events based on these registers
		≥ 0 (DFANA address)	enables the automatic display in the GUI of the total real power measured by a DFANA module connected to this DFCP. Note that, if you have more than one DFCP gateway, you should enable this option for one gateway only
		false	power display disabled for this DFCP
powersensivity	50	≥ 0	measured power changes are reported only if the difference from last reading is equal or greater than the power sensivity option, in Watts
powerinterval	1	≥ 0	power polling interval for the DFCC meter, in seconds
detectevents	false	true	generate forced events when a device is detected at start-up
		false	do not generate events when a device is detected at start-up
toolspassword		string	set this option with a long string (only letters and numbers) password to allow the remote connection of DFCP-IDE and other configuration tools to the DFCP gateways that are connected to HSYCO. For additional security, it is recommended to set this option only when required
language	english	en it fr	language for all messages from the DOMINO system: English, Italian or French

Initialization and Connection Events

Event name	Value	Description
connection	online	connection established to the DFCP module
	offline	HSYCO can’t connect to the DFCP module
detected.input.<n>.	model name	an input device of the type passed as value has been detected at address <n>, using addresses
detected.output.<n>.	model name	an output device of the type passed as value has been detected at address <n>, using addresses

The Device Configuration Database

The systemtopo.txt file contains the list of all devices and their individual input, output and virtual data points that could be directly associated to graphic object in the Web-based user interface. This file can be filled manually or automatically by HSYCO at start-up. To enable automatic discovery and automatic generation of devices’ information in the systemtopo file, use the inputdiscovery, outputdiscovery and virtualdiscovery options in the hsyco.ini configuration file. The default behavior is to only discover devices with output data points.

This is an example of an automatically generated systemtopo.txt file:

(devices)
domino.o10.1 : LIGHT ; LIGHT
domino.o6.1 : LIGHT ; DIMMER
domino.o7.2 : LIGHT ; LIGHT
domino.o7.1 : LIGHT ; DIMMER
domino.o9.2 : AUTOM ; VSHUT
domino.o5.4 : LIGHT ; LIGHT
domino.o9.1 : AUTOM ; VSHUT
domino.o5.3 : LIGHT ; LIGHT
domino.o5.2 : LIGHT ; LIGHT
domino.o5.1 : LIGHT ; LIGHT

You should then manually add comments and other optional parameters:

(devices)
domino.o10.1 : LIGHT ; LIGHT; main entrance light
domino.o6.1 : LIGHT ; DIMMER; lobby dimmer
domino.o7.2 : LIGHT ; LIGHT; kitchen workbench
domino.o7.1 : LIGHT ; DIMMER; kitchen main dimmer

DFCP Virtual Data Points and Registers

The DFCP implements 2032 virtual points for binary (on/off) data and 1024 registers for positive scalar values (0-65535).

All the virtual points and the registers can optionally generate I/O events. You can also write to the virtual data points and registers using the IO action in EVENTS or ioSet() method in Java.

You cannot directly control the DFCP virtual data points and registers using GUI objects.

To enable polling of the current state of the DFCP’s virtual data points, enable the virtualpoints options in hsyco.ini.

To enable polling of the current state of the DFCP’s registers, enable the registers options in hsyco.ini.

If you only have to write to virtual points or registers, enabling polling is not strictly required.

ID	Value	R/W	Description
v0.<n>	0	RW	virtual data point <n> off (<n>: 1-2032)
	1	RW	virtual data point <n> on (<n>: 1-2032)
r0.<n>	<x>	RW	register <n> off (<n>: 0-1023) set to value <x> (<x>: 0-65535)

DFCP Internal Clock

The DFCP module has an integrated real-time clock. You can use the clock datapoint to read the DFCP date and time, and set the DFCP clock to HSYCO’s current time.

ID	Value	R/W	Description
clock	yyyy-mm-dd hh:mm:ss	R	the DFCP clock current time
	read	W	read the DFCP clock, and the delta with HSYCO’s time
	sync	W	set the DFCP clock to HSYCO’s current time
clock.delta	integer number	R	the delta time in seconds between the DFCP and HSYCO clocks. A positive number means that the DFCP clock is ahead of HSYCO

DOMINO Modules Events and Control

Module Code	Description
DF4I	4 digital inputs
DFCK3	clock
DF8I	2x4 digital inputs
DF2R	2 outputs (relay)
DF4R, DF4RP	4 outputs (power relay)
DF4RP/I	4 generic inputs ON-OFF + 4 outputs
DFDI, DFDI2, DFDI2B, DFDM, DFDT	1 output (dimmer)
DFDMX	DMX interface
DFDALI	DALI interface
DFDV	1 output (1-10V - ballast) + 1 output (power relay)
DFTP	2 outputs (shutters)
DFTP/I	2 outputs (shutters) + 4 digital inputs
DFTR	2 outputs (shutters) + 1 output (relay)
DF4IL	4 digital inputs + 4 outputs (LED)
DF8IL	8 digital inputs + 8 outputs (LED)
DFAI	2 analog inputs
DFLUX, DFSUN	light sensor
DFCT/DFTZ	temperature sensor
DFRHT	temperature and humidity sensor
DFMETEO	weather module
DFCC	electric energy meter and load manager

DF4I

The DF4I is an input module with 4 digital inputs. It uses one address in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0	R	input pin 1 off
	1	R	input pin 1 on
i.<address>.2	0	R	input pin 2 off
	1	R	input pin 2 on
i.<address>.3	0	R	input pin 3 off
	1	R	input pin 3 on
i.<address>.4	0	R	input pin 4 off
	1	R	input pin 4 on

DFCK3

The DFCK3 is an input module for managing up to 15 different zones with an integrated clock. It uses one address in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0	R	input pin 1 off
	1	R	input pin 1 on
i.<address>.2	0	R	input pin 2 off
	1	R	input pin 2 on
i.<address>.3	0	R	input pin 3 off
	1	R	input pin 3 on
i.<address>.4	0	R	input pin 4 off
	1	R	input pin 4 on
i.<address>.5	0	R	input pin 5 off
	1	R	input pin 5 on
i.<address>.6	0	R	input pin 6 off
	1	R	input pin 6 on
i.<address>.7	0	R	input pin 7 off
	1	R	input pin 7 on
i.<address>.8	0	R	input pin 8 off
	1	R	input pin 8 on
i.<address>.9	0	R	input pin 9 off
	1	R	input pin 9 on
i.<address>.10	0	R	input pin 10 off
	1	R	input pin 10 on
i.<address>.11	0	R	input pin 11 off
	1	R	input pin 11 on
i.<address>.12	0	R	input pin 12 off
	1	R	input pin 12 on
i.<address>.13	0	R	input pin 13 off
	1	R	input pin 13 on
i.<address>.14	0	R	input pin 14 off
	1	R	input pin 14 on
i.<address>.15	0	R	input pin 15 off
	1	R	input pin 15 on

DF8I

The DF8I is an input module with 2x4 digital inputs. It uses two consecutive addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0	R	input pin 1 off
	1	R	input pin 1 on
i.<address>.2	0	R	input pin 2 off
	1	R	input pin 2 on
i.<address>.3	0	R	input pin 3 off
	1	R	input pin 3 on
i.<address>.4	0	R	input pin 4 off
	1	R	input pin 4 on
i.<address+1>.1	0	R	input pin 1 off
	1	R	input pin 1 on
i.<address+1>.2	0	R	input pin 2 off
	1	R	input pin 2 on
i.<address+1>.3	0	R	input pin 3 off
	1	R	input pin 3 on
i.<address+1>.4	0	R	input pin 4 off
	1	R	input pin 4 on

DF2R

The DF2R is an output module with 2 relay outputs. It uses one address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>.1	0 off	RW	output pin 1 off
	1 on	RW	output pin 1 on
o.<address>.2	0 off	RW	output pin 2 off
	1 on	RW	output pin 2 on

DF4R, DF4RP

The DF4R (DF4RP) is an output module with 4 relay outputs. It uses one address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>.1	0 off	RW	output pin 1 off
	1 on	RW	output pin 1 on
o.<address>.2	0 off	RW	output pin 2 off
	1 on	RW	output pin 2 on
o.<address>.3	0 off	RW	output pin 3 off
	1 on	RW	output pin 3 on
o.<address>.4	0 off	RW	output pin 4 off
	1 on	RW	output pin 4 on

DF4RP/I

The DF4RP/I is an output module with 4 generic inputs and 4 relay outputs. It uses one input address and one output address in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0	R	input pin 1 off
	1	R	input pin 1 on
o.<address>.1	0	RW	output pin 1 off
	1	RW	output pin 1 on
i.<address>.2	0	R	input pin 2 off
	1	R	input pin 2 on
o.<address>.2	0	RW	output pin 2 off
	1	RW	output pin 2 on
i.<address>.3	0	R	input pin 3 off
	1	R	input pin 3 on
o.<address>.3	0	RW	output pin 3 off
	1	RW	output pin 3 on
i.<address>.4	0	R	input pin 4 off
	1	R	input pin 4 on
o.<address>.4	0	RW	output pin 4 off
	1	RW	output pin 4 on

DFDM, DFDI, DFDI2, DFDI2B, DFDT

The DFDM, DFDI, DFDI2, DFDI2B and DFDT are output modules with 1 dimmer output. They use one address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>	program	R	program mode
	fault	R	dimmer fault
	auto	R	auto mode
	man	R	manual mode
o.<address>.1	off	RW	dimmer off
	1...100%	RW	percent dimmer level
	on	RW	dimmer on at last level
o.<address>.ramp	save	RW	saves the current ramp as default
	1...30	RW	ramp value in seconds (1 sec steps up to 10 and 2 sec steps up to 30)
	40, 50, 60	RW	ramp value in seconds (10 sec steps)
o.<address>.setpoint	0...1023	RW	setpoint level
o.<address>.hysteresis	0...255	RW	tolerance level
o.<address>.time	0...255	RW	period (seconds)

The dimmer level can be set using additional formats besides the standard percent values: - absolute positive integer number between 0 and 100 - percent number, formatted as x% - fractional format, formatted as “n/m”, where 0 <= n <= m.

DFDMX

The DFDMX is a DMX-512 protocol output module. It uses one address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>.<command>	0...255	RW	commands and values according to the DFDMX programming manual

DFDALI

The DFDALI is a DALI interface module. Using the DFDALI you can control up to 32 DALI devices. You can control individual devices, groups or broadcast commands to all devices. It uses one input (if enabled) and one output address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>	refresh	RW	queries the DFDALI module to update the current status of all DALI devices
o.<address>	off	RW	broadcast off command
o.<address>.all o.<address>.0	<level>	RW	broadcast level command
o.<address>.group.<DALI group>	off	RW	broadcast off command
	<level>	RW	group level command
o.<address>.<DALI address>	off	RW	turn off a single device
	<level>	RW	set a single device to a specific level
	> 100	RW	special functions, having values between 101 and 255, as defined in the DFDALI manual
i.<address>.polling	off	RW	polling mode is disabled
	on	RW	polling mode is enabled
i.<address>.test	0	RW	test button not pressed
	1	RW	test button pressed
i.<address>.dali	nopower	RW	power failure on the DALI bus
	open	RW	DALI bus is open
	short	RW	DALI bus is shorted
	on	RW	DALI bus on
i.<address>.1	fault	RW	DALI device 1 reporting a lamp failure
	unknown	RW	DALI device 1 status unknown

The DALI level can be set using additional formats besides the standard percent values: - absolute positive integer number between 0 and 100 - percent number, formatted as x% - fractional format, formatted as “n/m”, where 0 <= n <= m - special functions, having values between 101 and 255, as defined in the DFDALI manual.

DFDV

The DFDV is an output module with 1 output (1-10V for ballast) + 1 generic power relay output. It uses one address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>.1	off	RW	dimmer off
	1...100%	RW	percent dimmer level
	on	RW	dimmer on at last level
o.<address>.2	0	RW	output pin 1 off
	1	RW	output pin 1 on

The dimmer level can be set using additional formats besides the standard percent values: - absolute positive integer number between 0 and 100 - fractional format, formatted as “n/m”, where 0 <= n <= m. You can also set the value to “on” or “off”, that is equivalent to 1 and 0.

DFTP

The DFTP is an output module for 2 shutters. It uses one output address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>.1	up	RW	shutter up command
	down	RW	shutter down command
	stop off 0	RW	shutter stop command
	unknown	RW	unknown state
	offup	RW	shutter off, up position
	offdown	RW	shutter off, down position
o.<address>.2	up	RW	shutter up command
	down	RW	shutter down command
	stop off 0	RW	shutter stop command
	unknown	RW	unknown state
	offup	RW	shutter off, up position
	offdown	RW	shutter off, down position

DFTP/I

The DFTP is an input/output module for 2 shutters and 4 generic inputs. It uses one input and one output address in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0	R	input pin 1 off
	1	R	input pin 1 on
o.<address>.1	up	RW	shutter up command
	down	RW	shutter down command
	stop off 0	RW	shutter stop command
	unknown	RW	unknown state
	offup	RW	shutter off, up position
	offdown	RW	shutter off, down position
i.<address>.2	0	R	input pin 2 off
	1	R	input pin 2 on
o.<address>.2	up	RW	shutter up command
	down	RW	shutter down command
	stop off 0	RW	shutter stop command
	unknown	RW	unknown state
	offup	RW	shutter off, up position
	offdown	RW	shutter off, down position
i.<address>.3	0	R	input pin 3 off
	1	R	input pin 3 on
i.<address>.4	0	R	input pin 4 off
	1	R	input pin 4 on

DFTR

The DFTR is an output module with 1 shutter output and 1 relay output. It uses one address in the DOMINO bus.

ID	Value	R/W	Description
o.<address>.1	up	R	shutter up
	down	R	shutter down
	unknown	R	unknown state
	offup	R	shutter offup
	offdown	R	shutter offdown
o.<address>.2	0	R	output pin 2 off
	1	R	output pin 2 on

DF4IL

The DF4IL is an input/output module with 4 digital inputs and 4 digital open collector outputs for LEDs. It uses one input and one output address in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0 off	R	input pin 1 off
	1 on	R	input pin 1 on
o.<address>.1	0 off	RW	LED 1 off
	1 on	RW	LED 1 on
i.<address>.2	0 off	R	input pin 2 off
	1 on	R	input pin 2 on
o.<address>.2	0 off	RW	LED 2 off
	1 on	RW	LED 2 on
i.<address>.3	0 off	R	input pin 3 off
	1 on	R	input pin 3 on
o.<address>.3	0 off	RW	LED 3 off
	1 on	RW	LED 3 on
i.<address>.4	0 off	R	input pin 4 off
	1 on	R	input pin 4 on
o.<address>.4	0 off	RW	LED 4 off
	1 on	RW	LED 4 on

DF8IL

The DF8IL is an input/output module with 8 digital inputs and 8 digital open collector outputs for LEDs. It uses 4 input and 4 output addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0 off	R	input pin 1 off
	1 on	R	input pin 1 on
i.<address>.2	0 off	R	input pin 2 off
	1 on	R	input pin 2 on
i.<address>.3	0 off	R	input pin 3 off
	1 on	R	input pin 3 on
i.<address>.4	0 off	R	input pin 4 off
	1 on	R	input pin 4 on
i.<address+1>.1	0 off	R	input pin 5 off
	1 on	R	input pin 5 on
i.<address+1>.2	0 off	R	input pin 6 off
	1 on	R	input pin 6 on
i.<address+1>.3	0 off	R	input pin 7 off
	1 on	R	input pin 7 on
i.<address+1>.4	0 off	R	input pin 8 off
	1 on	R	input pin 8 on
i.<address+2>.1	0 off	R	LED 1 is off
	1 on	R	LED 1 is on
i.<address+2>.2	0 off	R	LED 2 is off
	1 on	R	LED 2 is on
i.<address+2>.3	0 off	R	LED 3 is off
	1 on	R	LED 3 is on
i.<address+2>.4	0 off	R	LED 4 is off
	1 on	R	LED 4 is on
i.<address+3>.1	0 off	R	LED 5 is off
	1 on	R	LED 5 is on
i.<address+3>.2	0 off	R	LED 6 is off
	1 on	R	LED 6 is on
i.<address+3>.3	0 off	R	LED 7 is off
	1 on	R	LED 7 is on
i.<address+3>.4	0 off	R	LED 8 is off
	1 on	R	LED 8 is on
v.<address+2>.1	0 off	RW	LED 1 is off
	1 on	RW	LED 1 is on
v.<address+2>.2	0 off	RW	LED 2 is off
	1 on	RW	LED 2 is on
v.<address+2>.3	0 off	RW	LED 3 is off
	1 on	RW	LED 3 is on
v.<address+2>.4	0 off	RW	LED 4 is off
	1 on	RW	LED 4 is on
v.<address+3>.1	0 off	RW	LED 5 is off
	1 on	RW	LED 5 is on
v.<address+3>.2	0 off	RW	LED 6 is off
	1 on	RW	LED 6 is on
v.<address+3>.3	0 off	RW	LED 7 is off
	1 on	RW	LED 7 is on
v.<address+3>.4	0 off	RW	LED 8 is off
	1 on	RW	LED 8 is on

Note that the first two output addresses are reserved and should not be used. Use address + 2 and address + 3 to control the LEDs.

DFIGLASS

The DFIGLASS is an input/output module with 6 touch buttons with addressable LEDs and a buzzer for audio feedback. It uses 1 input and 1 output addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0 off	R	button 1 off
	1 on	R	button 1 on
i.<address>.2	0 off	R	button 2 off
	1 on	R	button 2 on
i.<address>.3	0 off	R	button 3 off
	1 on	R	button 3 on
i.<address>.4	0 off	R	button 4 off
	1 on	R	button 4 on
i.<address>.5	0 off	R	button 5 off
	1 on	R	button 5 on
i.<address>.6	0 off	R	button 6 off
	1 on	R	button 6 on
i.<address>.fault	0 off	R	no fault
	1 on	R	touch keypad fault
i.<address>.led.1	0 off	RW	led 1 off
	1 on	RW	led 1 on
i.<address>.led.2	0 off	RW	led 2 off
	1 on	RW	led 2 on
i.<address>.led.3	0 off	RW	led 3 off
	1 on	RW	led 3 on
i.<address>.led.4	0 off	RW	led 4 off
	1 on	RW	led 4 on
i.<address>.led.5	0 off	RW	led 5 off
	1 on	RW	led 5 on
i.<address>.led.6	0 off	RW	led 6 off
	1 on	RW	led 6 on
i.<address>.backlight	0 off	RW	backlight off
	1 on	RW	backlight on
i.<address>.buzzer	0 off	RW	buzzer disabled
	1 on	RW	buzzer enabled

DF4I/V

The DF4I/V is an input/output module with 4 digital inputs and 12 digital virtual outputs. It uses four consecutive addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.1	0 off	R	input pin 1 off
	1 on	R	input pin 1 on
i.<address>.2	0 off	R	input pin 2 off
	1 on	R	input pin 2 on
i.<address>.3	0 off	R	input pin 3 off
	1 on	R	input pin 3 on
i.<address>.4	0 off	R	input pin 4 off
	1 on	R	input pin 4 on
v.<address+1>.1	0 off	RW	virtual pin 1 off
	1 on	RW	virtual pin 1 on
v.<address+1>.2	0 off	RW	virtual pin 2 off
	1 on	RW	virtual pin 2 on
v.<address+1>.3	0 off	RW	virtual pin 3 off
	1 on	RW	virtual pin 3 on
v.<address+1>.4	0 off	RW	virtual pin 4 off
	1 on	RW	virtual pin 4 on
v.<address+2>.1	0 off	RW	virtual pin 1 off
	1 on	RW	virtual pin 1 on
v.<address+2>.2	0 off	RW	virtual pin 2 off
	1 on	RW	virtual pin 2 on
v.<address+2>.3	0 off	RW	virtual pin 3 off
	1 on	RW	virtual pin 3 on
v.<address+2>.4	0 off	RW	virtual pin 4 off
	1 on	RW	virtual pin 4 on
v.<address+3>.1	0 off	RW	virtual pin 1 off
	1 on	RW	virtual pin 1 on
v.<address+3>.2	0 off	RW	virtual pin 2 off
	1 on	RW	virtual pin 2 on
v.<address+3>.3	0 off	RW	virtual pin 3 off
	1 on	RW	virtual pin 3 on
v.<address+3>.4	0 off	RW	virtual pin 4 off
	1 on	RW	virtual pin 4 on

DFAI

The DFAI is an input module (0-10V) with 2 analog inputs. It uses two consecutive input addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>	0...1000	R	input voltage in Volt/100
i.<address+1>	0...1000	R	input voltage in Volt/100

DFLUX, DFSUN

The DFLUX and DFSUN are input modules with 1 analog light sensor. They use one input address in the DOMINO bus.

ID	Value	R/W	Description
i.<address>	0...1023	R	lux level (raw level, not translated to the lux range)

DFCT

The DFCT is an input/output temperature sensor module. It uses two consecutive input addresses and five consecutive output addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.mode	winter	R	winter mode
	summer	R	summer mode
i.<address>.fan	min	R	min fan speed
	med	R	medium fan speed
	max	R	max fan speed
	off	R	fan off
i.<address>.fan.mode	man	R	manual fan mode
	auto	R	auto fan mode
i.<address>.setpoint	1	R	setpoint 1
	2	R	setpoint 2
	3	R	setpoint 3
	off	R	off
	man	R	manual setpoint
i.<address>.setpoint.mode	man	R	manual setpoint mode
	auto	R	auto setpoint mode
i.<address>.temp	<temp>	R	temperature value (in C/10)
	fault	R	temperature sensor fault
i.<address>.status	off	R	off
	cooling	R	cooling status mode
	heating	R	heating status mode
o.<address>.mode	winter	RW	winter mode
	summer	RW	summer mode
o.<address>.fan	min	RW	min fan speed
	med	RW	medium fan speed
	max	RW	max fan speed
	off	RW	fan off
o.<address>.fan.mode	man	RW	manual fan mode
	auto	RW	auto fan mode
o.<address>.setpoint	1	RW	setpoint 1
	2	RW	setpoint 2
	3	RW	setpoint 3
	0 off	RW	setpoint off
	man	RW	manual setpoint
o.<address>.setpoint.temp.1	<temp>	RW	temperature setpoint 1 value (in C/10)
o.<address>.setpoint.temp.2	<temp>	RW	temperature setpoint 2 value (in C/10)
o.<address>.setpoint.temp.3	<temp>	RW	temperature setpoint 3 value (in C/10)
o.<address>.setpoint.temp.man	<temp>	RW	temperature manual setpoint 1 value (in C/10)
o.<address>.program.summer o.<address>.program.winter	refresh	RW	forces to daily summer/winter program for all days of the week
o.<address>.program.summer.<day> o.<address>.program.winter.<day>	refresh	RW	forces to daily summer/winter program for the reported day (mon:1, sun:7)
	<s0>...<s47>	RW	48 character represents the daily setpoint program divided in time slots of 30 minutes

DFTZ

The DFTZ is an input/output temperature sensor module. It uses 3 consecutive input addresses and 4 consecutive output addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.mode	winter	R	winter mode
	summer	R	summer mode
i.<address>.setpoint	comfort	R	comfort setpoint
	eco	R	eco setpoint
	off	R	off
i.<address>.temp	<temp>	R	temperature value (in C/10)
	fault	R	temperature sensor fault
i.<address>.status	off	R	off
	cooling	R	cooling status mode
	heating	R	heating status mode
o.<address>.mode	winter	RW	winter mode
	summer	RW	summer mode
o.<address>.setpoint	comfort	RW	comfort setpoint
	eco	RW	eco setpoint
	0 off	RW	off
o.<address>.setpoint.temp.comfort	<temp>	RW	comfort setpoint value (in C/10)
o.<address>.setpoint.temp.eco	<temp>	RW	eco setpoint value (in C/10)
o.<address>.setpoint.temp.limit	<temp>	RW	summer/winter setpoint temperature limit (in C/10)

DFRHT

The DFRHT is a temperature and humidity sensor. It uses four consecutive input addresses and two consecutive output addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.humidity	0...100	R	relative percent umidity
i.<address>.temp	<temp>	R	temperature value
i.<address>.dewpoint	<temp>	R	dew point value
i.<address>.dewpoint.limit.1	0	R	dew point is lower than limit 1
	1	R	dew point is higher than limit 1
	<temp>	RW	dew point limit 1
	off	RW	limit 1 not set
i.<address>.dewpoint.limit.2	0	R	dew point is lower than limit 2
	1	R	dew point is higher than limit 2
	<temp>	RW	dew point limit 2
	off	RW	limit 2 not set

DFMETEO

The DFMETEO is the weather sensor module. It uses four consecutive input addresses and three consecutive output addresses in the DOMINO bus.

ID	Value	R/W	Description
i.<address>.temp	<temp>	RW	temperature value (in C/10)
	off	RW	limit not set
i.<address>.lux	<lux*10>	R	lux level according to the DFLUX range
	<lux>	RW	lux limit
	0	RW	limit not set
i.<address>.wind	1 m/s /10	R	wind value
	m/s	RW	wind limit
	0	RW	limit not set
i.<address>.rain	0	R	no rain
	1	R	rain
i.<address>.night	0	R	day
	1	R	night
i.<address>.temp.limit	0	R	measured temp is less than limit
	1	R	measured temp is greater than limit
i.<address>.lux.limit	0	R	measured lux is less than limit
	1	R	measured lux is greater than limit
i.<address>.wind.limit	0	R	measured wind is less than limit
	1	R	measured wind is greater than limit
i.<address>.light.south	0	R	light is not coming from south
	1	R	light is coming from south
i.<address>.light.west	0	R	light is not coming from west
	1	R	light is coming from west
i.<address>.light.east	0	R	light is not coming from east
	1	R	light is coming from east
i.<address>.fault	0	R	sensor not fault
	1	R	sensor fault

DFCC

The DFCC is an energy meter and load manager module. In the following table, <N> is the sequential index (1 to 3) of the DFCC module.

ID	Value	R/W	Description
energy.<n>.power.real	0...65535	R	real power (Watt)
energy.<n>.power.reactive	-32768...+32767	R	reactive power (var)
energy.<n>.power.apparent	-32768...+32767	R	apparent power (VA)
energy.<n>.power.realavg	0...65535	R	average real power (Watt)
energy.<n>.power.reactiveavg	-32768...+32767	R	average reactive power (var)
energy.<n>.cos	-1000...+1000	R	cos(φ) * 1000
energy.<n>.load.1	0	R	load 1 disabled
	1	R	load 1 enabled
energy.<n>.load.2	0	R	load 2 disabled
	1	R	load 2 enabled
energy.<n>.load.3	0	R	load 3 disabled
	1	R	load 3 enabled
energy.<n>.load.4	0	R	load 4 disabled
	1	R	load 4 enabled
energy.<n>.load.5	0	R	load 5 disabled
	1	R	load 5 enabled
energy.<n>.load.6	0	R	load 6 disabled
	1	R	load 6 enabled
energy.<n>.load.7	0	R	load 7 disabled
	1	R	load 7 enabled
energy.<n>.load.8	0	R	load 8 disabled
	1	R	load 8 enabled

DFANA

Network analyzer module for Domino bus. Uses up to 20 consecutive input addresses and, if enabled, 1 output address equal to the base input address.

ID	Value	R/W	Description
i.<address>.v12	[V]	R	chained voltage phase 1-2
i.<address>.v23	[V]	R	chained voltage phase 2-3
i.<address>.v31	[V]	R	chained voltage phase 3-1
i.<address>.vtm	[V]	R	average chained voltage
i.<address>.i1	[A]	R	current phase 1
i.<address>.i2	[A]	R	current phase 2
i.<address>.i3	[A]	R	current phase 3
i.<address>.itm	[A]	R	average current
i.<address>.ptot	[W]	R	total active power
i.<address>.ptotk	[kW]	R	total active power
i.<address>.qtot	[W]	R	total reactive power
i.<address>.qtotk	[kW]	R	total reactive power
i.<address>.pf	[pf]	R	total power factor
i.<address>.frequency	[Hz]	R	frequency
i.<address>.v1n	[V]	R	voltage phase 1
i.<address>.v2n	[V]	R	voltage phase 2
i.<address>.v3n	[V]	R	voltage phase 3
i.<address>.p1	[W]	R	active power phase 1
i.<address>.p1k	[kW]	R	active power phase 1
i.<address>.p2	[W]	R	active power phase 2
i.<address>.p2k	[kW]	R	active power phase 2
i.<address>.p3	[W]	R	active power phase 3
i.<address>.p3k	[kW]	R	active power phase 3

User Interface

All DOMINO devices data points that have been defined in the systemtopo.txt database are automatically listed in the Project Editor. Adding a button to control a device output point requires just a few clicks and no additional EVENTS logic.

Besides the direct association of control buttons and data points, the DOMINO driver also automatically updates graphical objects that represent values or states of complex devices, like the DFCT temperature control unit. It will also automatically intercept buttons to manually set operation modes and temperature set-points.

---

DFDMX

You can define a standard HSYCO DMX server for each DFDMX module, then use the dmx and dmxrgb objects to control channels 1-64 of the DMX bus connected to the DFDMX module.

For example:

dmxServers = dmx
dmxServersId.dmx = domino.o8

 Note that, instead of defining the dmxServersIP parameter, the dmxServersId is used to associate the DMX server with the id of the DFDMX module.

---

DFCC

UISET Actions

ID	Attribute	Set to
energy.<n>.power	value	real power, followed by “ W”

---

DFCT

UISET Actions

ID	Attribute	Set to
<address>.mode	summer	summer mode (cooling)
	winter	winter mode (heating)
<address>.mode.label.summer	visible	the DFCT is in summer mode
<address>.mode.label.winter	visible	the DFCT is in winter mode
<address>.status	off	zone off
	on	zone on
<address>.status.label.cooling	visible	if the zone is cooling
<address>.status.label.heating	visible	if the zone is heating
<address>.fan	off	fan off
	min	minimum fan speed
	med	medium fan speed
	max	maximum fan speed
<address>.fan.label.min	visible	the fan speed is min
<address>.fan.label.med	visible	the fan speed is med
<address>.fan.label.max	visible	the fan speed is max
<address>.fan.mode	man	manual fan mode
	auto	auto fan mode
<address>.setpoint	1,2,3	active setpoint
	man	manual setpoint
	off	zone off
<address>.setpoint.label.1	visible	setpoint 1 is active
<address>.setpoint.label.2	visible	setpoint 2 is active
<address>.setpoint.label.3	visible	setpoint 3 is active
<address>.setpoint.label.man	visible	manual setpoint is active
<address>.setpoint.label.off	visible	zone is off
<address>.setpoint.mode	man	manual setpoint mode
	auto	auto setpoint mode
<address>.setpoint.temp	<value>	the active setpoint temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.setpoint.temp.1	<value>	the active setpoint 1 temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.setpoint.temp.2	<value>	the active setpoint 2 temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.setpoint.temp.3	<value>	the active setpoint 3 temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.setpoint.temp.man	<value>	the manual setpoint temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.temp	<temp>	the manual setpoint temperature, in Celsius degrees with one decimal digit, followed by " °C"
	fault	fault/error condition

USER Commands

Name	Param	Action
<address>	mode	cycle through summer and winter mode
	mode.summer	set summer mode (cooling)
	mode.winter	set winter mode (heating)
	fan	cycle through fan speeds and modes (auto, off, man/min, man/med, man/max, auto)
<address>.setpoint	mode	cycle through the manual, automatic and off operation modes
	mode.man	set manual operation mode
	mode.auto	set automatic operation mode
	mode.off	off mode
	temp.1.up	increase setpoint 1 temperature in 0.5C steps
	temp.1.down	decrease setpoint 1 temperature in 0.5C steps
	temp.1.<t>	setpoint 1 set to temperature t, in C/10 (0 <= t <= 355)
	temp.2.up	increase setpoint 2 temperature in 0.5C steps
	temp.2.down	decrease setpoint 2 temperature in 0.5C steps
	temp.2.<t>	setpoint 2 set to temperature t, in C/10 (0 <= t <= 355)
	temp.3.up	increase setpoint 3 temperature in 0.5C steps
	temp.3.down	decrease setpoint 3 temperature in 0.5C steps
	temp.3.<t>	setpoint 3 set to temperature t, in C/10 (0 <= t <= 355)
	temp.man.up	increase manual setpoint temperature in 0.5C steps
	temp.man.down	decrease manual setpoint temperature in 0.5C steps
	temp.man.<t>	manual setpoint set to temperature t, in C/10 (0 <= t <= 355)
<address>.fan	mode	cycle through the manual and automatic fan speed modes
	mode.man	set manual fan speed mode
	mode.auto	set automatic fan speed mode
	up	increase fan speed
	down	decrease fan speed
	min	set min fan speed
	med	set med fan speed
	max	set max fan speed
	off	fan off

---

DFTZ

UISET Actions

ID	Attribute	Set to
<address>.mode	summer	summer mode (cooling)
	winter	winter mode (heating)
<address>.mode.label.summer	visible	the DFTZ is in summer mode
<address>.mode.label.winter	visible	the DFTZ is in winter mode
<address>.status	off	zone off
	on	zone on
<address>.status.label.off	visible	if the zone is not cooling or heating
<address>.status.label.cooling	visible	if the zone is cooling
<address>.status.label.heating	visible	if the zone is heating
<address>.setpoint	com	comfort setpoint
	man	manual setpoint
	off	zone off
<address>.setpoint.label.1	visible	comfort setpoint is active
<address>.setpoint.label.2	visible	eco setpoint is active
<address>.setpoint.label.off	visible	zone is off
<address>.setpoint.temp	<value>	the active setpoint temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.setpoint.temp.1	<value>	the comfort setpoint temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.setpoint.temp.2	<value>	the eco setpoint temperature, in Celsius degrees with one decimal digit, followed by " °C"
<address>.setpoint.temp.man	<value>	the summer or winter setpoint temperature limit, in Celsius degrees with one decimal digit, followed by " °C"
<address>.temp	<temp>	the manual setpoint temperature, in Celsius degrees with one decimal digit, followed by " °C"
	fault	fault/error condition

USER Commands

Name	Param	Action
<address>	mode	cycle through summer and winter mode
	mode.summer	set summer mode (cooling)
	mode.winter	set winter mode (heating)
<address>.setpoint	mode	cycle through the manual, automatic and off operation modes
	mode.comfort	set comfort operation mode
	mode.eco	set eco operation mode
	mode.off	off mode
	temp.up	increase the active setpoint temperature in 0.5C steps
	temp.down	ddecrease the active setpoint temperature in 0.5C steps
	temp.<t>	active setpoint set to temperature t, in C/10 (0 <= t <= 355)
	temp.1.up	increase comfort setpoint temperature in 0.5C steps
	temp.1.down	decrease comfort setpoint temperature in 0.5C steps
	temp.1.<t>	comfort setpoint set to temperature t, in C/10 (0 <= t <= 355)
	temp.2.up	increase eco setpoint temperature in 0.5C steps
	temp.2.down	decrease eco setpoint temperature in 0.5C steps
	temp.2.<t>	eco setpoint set to temperature t, in C/10 (0 <= t <= 355)
	temp.man.up	increase setpoint temperature limit in 0.5C steps
	temp.man.down	decrease setpoint temperature limit in 0.5C steps
	temp.man.<t>	set-point temperature limit set to temperature t, in C/10 (0 <= t <= 355)

Release Notes

3.2.2

bug fixes:

• the toolspassword optional parameter was incorrectly converted to lower case
• fixed a bug that prevented reading the input pins of DF4RP/I and DF4RPR/I

3.2.1

• support for DFTZ

3.2.0

• support for DFIGLASS
• new "detectevents" option, generates forced events when a device is detected at start-up
• support for the toolspassword option, to allow DFCP-IDE and other tools secure remote access to the DFCP via HSYCO
• new clock datapoint to read the DFCP internal clock and set it to HSYCO's time

3.1.2

bug fixes:

• the (temp) object's DFCT configuration function was broken in HSYCO 3.1.0
• energy metering data point were not updated

3.1.1

• added support for DF4RP/I and DFDT

3.1.0

• added support for DFANA energy meter module

3.0.3

• optimized performance of DFCP’s registers status polling

3.0.1

• you can now limit the number of virtual points and registers read and written by HSYCO, and have access to all of the 1024 registers; defaults are unchanged
• added support for DF8IL, DFDI2B and DFRHT modules

3.0.0

• update DFDMX state at startup
• support for failover mode

1.2.0

• fixed bugs related to the DFDM and DFDI modules
• integration with the DMX server engine
• enhanced GUI support for DFCC and DFCT

1.1.0

• automatic generation of the device map in systemtopo.txt
• Web Editor support
• support for DFCP’s virtual data points and registers
• support for serial connection to the DFCP through the serial ports of HWg PortBox and ERxx network devices

1.0.0

• initial release

---

HSYCO and Home Systems Consulting are registered trademarks of Home Systems Consulting SpA. Java and JavaScript are registered trademarks of Oracle and/or its affiliates. DOMINO and DUEMMEGI are registered trademarks of DUEMMEGI SRL. Other products or company names can be trademarks or registered trademarks of other companies and are used for demonstrative purposes only, with no violation intent.