Fp2000

Aritech Interlogix FP2000 is a multi-area fire panel. The integration with HSYCO can be accomplished via direct control through the RS232 port on the panel. The FP2000 I/O Server in HSYCO supports the integration of more than one unit within the same HSYCO interface.

Communication

Employ an RS-232 cable to connect the panel directly to HSYCO.

RS-232 parameters:

Baud rate	same as panel settings (default 9600)
Data bits	8
Stop bit	1
Parity	none
Flow control	RTS/CTS

HSYCO Configuration

Options

ID	Default	Values	Description
gui	true	true	enable support for the UI object, UISET actions and USER commands
		false	disable UI support
startupevents	false	true	generate IO events also during the driver’s start-up phase
		false	start generating events only after HSYCO is aligned with the current status of the system
accesscode	0	0	do not request for authentication (the I/O Server will only be usable as panel emulator)
		1 - 9999	use the specified value as access code for requesting authentication
keypaddisable	false	true	disable the emulator keypad buttons
		false	the emulator keypad buttons are enabled
controldisable	false	true	disable the emulator control buttons
		false	the emulator control buttons are enabled
displayhlcolor	339933	000000 - FFFFFF	use the specified hexadecimal value as the highlight color for the display of the emulator

User Interface

Ats Object

The user interface for the Aritech ATS multi-area intrusion detection system:

The Ats object is listed in the Project Editor’s new object list only when at least one Aritech ATS I/O Server is defined.

Parameters

• server id: the server ID
• position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(ats <server id>; <position>)

E.g.

(ats serverid; x10y20)

UISET Actions

ID	Value	R/W	Description
connection	online	R	connection established
	offline	R	HSYCO can't connect to the panel
emulation	1	R	emulation is active
		W	activate emulation
	0	R	emulation is disabled
		W	disable emulation
led.general.fire.1 led.general.fire.2 led.general.processor led.general.supply.fault led.general.disabled led.general.fault led.general.supply led.general.system.fault led.brigade.delay.off led.brigade.delay.on led.brigade.stop led.brigade.fault led.brigade.signal led.sounder.delay.on led.sounder.silence led.sounder.fault led.sounder.sound led.sounder.delay.off led.control.test led.control.disabled led.control.silence.buzzer led.all led.panel	on	R	the corresponding LED is on
	off	R	the corresponding LED is off
	blink	W	the corresponding LED is on, blinking
status.alarm.count	<num>	R	count of fires
status.fault.count	<num>	R	count of faults
status.condition.count	<num>	R	count of conditions
status.event.count	<num>	R	count of all the events other than fire, fault or condition
clock	<date_time>	R	the panel’s clock is set to <date_time>. The value has the format "yyyy-mm-dd hh:mm:ss" (e.g. "2012-12-30 16:59:23")
		W	set the data and time of the panel to <date_time>. The value has the format "yyyy-mm-dd hh:mm:ss" (e.g. "2012-12-30 16:59:23")
	read	W	request for reading date and time set on the panel

ID	Attribute	Set to
log	value	latest security log lines (as many as specified by the 'logsize' option)
log0	value	latest line of the security log when a new entry is added, set back to blank after a short period
a<n>.name	value	name assigned to area <n>
z<n>.name	value	name assigned to zone <n>
connection.label	visible	true	when datapoint connection = offline
		false	when datapoint connection = online
<datapoint_id>.label.1	visible	true	when datapoint with ID <datapoint_id> has value '1'
		false	when datapoint with ID <datapoint_id> has value '0'
<datapoint_id>.label.0	visible	true	when datapoint with ID <datapoint_id> has value '0'
		false	when datapoint with ID <datapoint_id> has value '1'

USER Commands

Name	Param	Action
armed	1	arm all active areas
	0	disarm all active areas
alarm	reset	reset system alarms
a<n>.armed	1	arm area <n>
	0	disarm area <n>
	force	force arm area <n>
z<n>.isolated	1	isolate zone <n>
	0	de-isolate zone <n>
z<n>.alarm	reset	reset alarms on zone <n>
o<n>.active	1	activate output <n>
	0	deactivate output <n>