Boschfpa

The BOSCH FPA-5000 is a modular fire panel system.

This I/O server requires the FPA firmware version 2.12.7 or later.

Communication

Be sure to use BOSCH sofware management tool RPS version 4_0_11 or later for the FPA configuration.

Configure the RS232 Communication Module module as follows:

After the upload configuration process the FPA-5000 is ready to be connected via RS232.

RS232 Communication Module overview:

RS-232 parameters:

Baud rate	9600
Data bits	7
Stop bit	1
Parity	even
Flow control	none

HSYCO Configuration

Add a BOSCHFPA I/O Server in the I/O Servers section of the Settings and set its parameters:

Communication

• Comm ID: select the comm port connected to the panel.

High Availability

• Shutdown when inactive: defaults to true.

Options

ID	Default	Values	Description
gui	true	true	enable support for the UI (event log object)
		false	disable UI support
language	system language	en	language of log and display messages. Supported values are English, Italian and German
		it
		de
logsize	100	n ≥ 0	the number of log lines to display in the UI object

boschfpa.ini

The boschfpa.ini file is an optional configuration file located in the main directory (same directory as hsyco.ini or hsyco.jar) and used to define zones (lines) names. If defined, these names will be used instead of the original numbers in the log files and GUI event log object.

Changes to the boschfpa.ini file are automatically detected and don't require a restart to become effective.

 This file is case sensitive.

For each zone (line), enter a line formatted as:

<io_server_id>.line.<logical address>.<subaddress> = <name>

For instance:

fpa.line.3.1 = DATA ROOM SENSOR
fpa.line.4.1 = GENERATORS ROOM

Datapoints

ID	Value	R/W	Description
connection	online	R	connection established
	offline	R	HSYCO can't connect to the panel
buzzer	off	R	buzzer silenced (forced event)
		W	silence the buzzer
line.<logical address>.<subaddress>	bypass	R	bypass
	blocked	R	blocked
	warningthreshold	R	threshold warning
	tamper	R	tamper alarm
	alarminvestigation	R	alarm verification
	invalid	R	invalid
	fire	R	fire
	fireprealarm	R	fire pre-alarm
	firedaymode	R	fire day mode
	normal	R	normal
	fault	R	fault
	troublelight	R	minor fault
	supervisorymonitorwater	R	supervisory, monitor, water
	off	R	off
	on	R	on
	paperout	R	out of paper
	powerfail	R	power fail
	activated	R	activated
	pollution	R	heavy contamination
	pollutionlight	R	minor contamination
	walktestfire	R	walk test fire
	walktestnormal	R	walk test normal
	walktesttrouble	R	walk test fault
	walktestoff	R	walk test off
	walkteston	R	walk test on
	walktestactivation	R	walk test activation
status.bypass status.blocked status.warningthreshold status.tamper status.alarminvestigation status.invalid status.fire status.fireprealarm status.firedaymode status.normal status.trouble status.troublelight status.supervisorymonitorwater status.off status.on status.paperout status.powerfail status.activated status.pollution status.pollutionlight status.walktestfire status.walktestnormal status.walktesttrouble status.walktestoff status.walkteston status.walktestactivation	1	R	one or more lines in this state
	0	R	no lines in this state

User Interface

Bentel Object

The user interface for the Bentel KYO320 multi-area intrusion detection system:

The Bentel object is listed in the Project Editor’s new object list only when at least one Bentel I/O Server is defined.

Parameters

• server id: the server ID
• position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(bentel <server id>; <position>)

E.g.

(bentel serverid; x10y20)

UISET Actions

ID	Attribute	Set to
areas	value	the status of all partitions
log0	value	the latest entry of the security log for a short period
logs	value	the latest entries of the security log (as many as specified in hsyco.ini)
zones	value	the status of all known zones (zones are added to this list as soon as an event is detected on a zone)
connection.label.online	visible	true when the panel is connected to HSYCO, false otherwise
connection.label.offline	visible	true when the panel is not connected to HSYCO, false otherwise
partition.<n>.label.alarm	visible	true when partition <n> alarm is active, false otherwise
partition.<n>.label.armed	visible	true when partition <n> is armed, false otherwise
partition.<n>.label.disarmed	visible	true when partition <n> is disarmed, false otherwise
partition.<n>.label.away	visible	true when partition <n> is armed in away mode, false otherwise
partition.<n>.label.stay	visible	true when partition <n> is armed in stay mode, false otherwise
partition.<n>.label.staynodelay	visible	true when partition <n> is armed in stay no delay mode, false otherwise
zone.<n>.label.alarm	visible	true when zone <n> alarm is active
zone.<n>.label.tamper	visible	true when zone <n> tamper alarm is active
zone.<n>.label.disabled	visible	true when zone <n> is disabled