Boschmap

The Bosch MAP panels are multi-area intrusion detection systems.

The integration with HSYCO can be accomplished via Ethernet connection.

HSYCO Configuration

Add a BOSCHMAP I/O Server in the I/O Servers section of the Settings and set its parameters:

Communication

IP Address: IP address of the panel
IP Port: TCP/IP port to use, leave blank to use default port 6793.

Authentication

Password: password set on for the BIS user. Leave blank to use the default password.

High Availability

Shutdown when inactive: defaults to true.

Options

ID	Default	Values	Description
startupevents	false	true	generate IO events also during the driver’s start-up phase
startupevents	false	false	start generating events only after HSYCO is aligned with the current status of the system
pollinterval	30	n > 0	number of seconds between consecutive requests of the open status of points. A low value can overload the panel

boschmap.ini

The boschmap.ini file is a specific configuration file located in the root directory. This file is required to specify which areas and points are configured on the panel and to assign them a name.

Add a new line for each area followed by a new line for each point belonging to that area, using the following format:

<io_server_id>.<area_siid> = <name>
<io_server_id>.<point_siid> = <name>

where <area_siid>/<point_siid> is the security identifier of the area/point as specified in the configuration software of the panel.

For instance:

bsc.1.1.ControlPanelArea.1.1 = Control Panel

bsc.1.1.Area.2.4 = Internal area
	bsc.1.1.Point.01001.006 = Front door
	bsc.1.1.Point.01001.007 = Back door

bsc.1.1.Area.2.5 = External area
	bsc.1.1.Point.01001.008 = Gate

specifies three areas: the Control Panel area with no points, an internal area with two points and an external area with one point.

Datapoints

ID	Value	R/W	Description
connection	online	R	connection established
connection	offline	R	HSYCO can't connect to the panel
alarm^{[Note 1]}	0	R	no alarm
alarm^{[Note 1]}	1	R	alarm active
armed	0	R	no area armed
armed	1	R	at least one area armed
trouble^{[Note 1]}	0	R	no trouble
trouble^{[Note 1]}	1	R	trouble active
tamper^{[Note 1]}	0	R	no tamper
tamper^{[Note 1]}	1	R	tamper active
user.tamper^{[Note 1]}	0	R	no user tamper
user.tamper^{[Note 1]}	1	R	user tamper active
<siid>.name	<name>	R	the name of the area/point is set to <name>
<area_siid>.armed	0	R	area disarmed
	0	W	disarm the area
	1	R	area all armed, delayed
	1	W	arm all the area, delayed
	2	R	area all armed, delayed with bypass
	2	W	arm all the area, instant
	3	R	area all armed, instant
	3	W	arm the area partially, delayed
	4	R	area al armed, instant with bypass
	4	W	arm the area partially, instant
	5	R	area partially armed, delayed
	5	W	custom-arm the area, delayed
	6	R	area partially armed, delayed with bypass
	6	W	custom-arm the area, instant
	7	R	area partially armed, instant
	7	W	arm all the area, delay zero
	8	R	area partially armed, instant with bypass
	8	W	arm the area partially, delay zero
	9	R	area custom armed, delayed
	9	W	custom-arm the area, delay zero
	10	R	area custom armed, delayed with bypass
	11	R	area custom armed, instant
	12	R	area custom armed, instant with bypass
<area_siid>.clearmem	1	W	clear active events (alarm, trouble etc) in the area
<x>.<y>.area.0.0.clearmem	1	W	clear active events from all level 2 areas (except Control Panel Areas)
<area_siid>.ready.arm.instant	0	R	the area is not ready to be armed instantly
<area_siid>.ready.arm.instant	1	R	the area is ready to be armed instantly
<area_siid>.ready.arm.delay	0	R	the area is not ready to be armed with delay
<area_siid>.ready.arm.delay	1	R	the area is ready to be armed with delay
<area_siid>.ready.disarm	0	R	the area is not ready to be disarmed
<area_siid>.ready.disarm	1	R	the area is ready to be disarmed
<area_siid>.force.instant	0	R	the area is not ready to be force armed instantly
<area_siid>.force.instant	1	R	the area is ready to be force armed instantly
<area_siid>.force.delay	0	R	the area is not ready to be force armed with delay
<area_siid>.force.delay	1	R	the area is ready to be force armed with delay
<area_siid>.bypassed	0	R	no bypassed devices in this area
<area_siid>.bypassed	1	R	there are bypassed devices in this area
<area_siid>.alarm	0	R	no active alarm
<area_siid>.alarm	1	R	alarm active
<area_siid>.trouble	0	R	no trouble
<area_siid>.trouble	1	R	trouble active
<area_siid>.tamper	0	R	no tamper
<area_siid>.tamper	1	R	tamper active
<point_siid>.blocked	0	R	point not blocked
<point_siid>.blocked	1	R	point blocked
<point_siid>.bypassed	0	R	point not bypassed
	0	W	unbypass point
	1	R	point bypassed swinger
	1	W	bypass point
	2	R	point bypassed auto
	3	R	point bypassed force
	4	R	point bypassed manual
<point_siid>.open	0	R	point closed
	1	R	point open
	read	W	request the reading of the point's open state
<point_siid>.alarm^{[Note 2]}	0	R	no alarm
<point_siid>.alarm^{[Note 2]}	1	R	alarm
<point_siid>.holdup^{[Note 2]}	0	R	no holdup alarm
<point_siid>.holdup^{[Note 2]}	1	R	holdup alarm
<point_siid>.duress^{[Note 2]}	0	R	no duress alarm
<point_siid>.duress^{[Note 2]}	1	R	duress alarm
<point_siid>.tamper^{[Note 2]}	0	R	no tamper alarm
<point_siid>.tamper^{[Note 2]}	1	R	tamper alarm
<device_siid>.tamper^{[Note 2]}	0	R	no tamper alarm
<device_siid>.tamper^{[Note 2]}	1	R	device tampered
<device_siid>.trouble^{[Note 2]}	0	R	no trouble
<device_siid>.trouble^{[Note 2]}	1	R	trouble on device
<device_siid>.alarm^{[Note 2]}	0	R	no alarm
<device_siid>.alarm^{[Note 2]}	1	R	alarm on device
<device_siid>.active^{[Note 2]}	0	R	device deactivated
<device_siid>.active^{[Note 2]}	1	R	device active

Note 1: These datapoints are only updated after the startup phase, i.e. events are generated only for events occurring after the driver is online.

Note 2: These datapoints, if their value is 1, generate events at startup even if the startupevents option is set to false.

Release Notes

3.5.0

added "clearmem" datapoints
added "armed" datapoint
improved communication error handling

3.4.0

initial version release

Bosch is a registered trademark of Bosch Security Systems.