Fp2000

From HSYCO
Revision as of 16:47, 10 January 2014 by Hsyco (talk | contribs) (Created page with "Aritech Interlogix FP2000 is a multi-area fire panel. The integration with HSYCO can be accomplished via direct control through the RS232 port on the panel. The FP2000 I/O Ser...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Aritech Interlogix FP2000 is a multi-area fire panel. The integration with HSYCO can be accomplished via direct control through the RS232 port on the panel. The FP2000 I/O Server in HSYCO supports the integration of more than one unit within the same HSYCO interface.

Communication

Employ an RS-232 cable to connect the panel directly to HSYCO.

RS-232 parameters:

Baud rate same as panel settings (default 9600)
Data bits 8
Stop bit 1
Parity none
Flow control RTS/CTS


HSYCO Configuration

Options

ID Default Values Description
gui true true enable support for the UI object, UISET actions and USER commands
false disable UI support
startupevents false true generate IO events also during the driver’s start-up phase
false start generating events only after HSYCO is aligned with the current status of the system
accesscode 0 0 do not request for authentication (the I/O Server will only be usable as panel emulator)
1 - 9999 use the specified value as access code for requesting authentication
keypaddisable false true disable the emulator keypad buttons
false the emulator keypad buttons are enabled
controldisable false true disable the emulator control buttons
false the emulator control buttons are enabled
displayhlcolor 339933 000000 - FFFFFF use the specified hexadecimal value as the highlight color for the display of the emulator

Datapoints

ID Value R/W Description
connection online R connection established
offline R HSYCO can't connect to the panel
armed 1 R at least one area is armed
W arm all active areas
0 R no area is armed
W disarm all active areas
alarm 1 R at least one area is in alarm
0 R no area is in alarm
reset W reset system alarms
clock read W request the reading of the panel’s clock value
<date_time> R the panel’s clock is set to <date_time>. The value has the format "yyyy-mm-dd hh:mm:ss" (e.g. "2012-12-30 16:59:23").

This event is only triggered after a request.

a<n>.name <text> R area <n> has been assigned the name <text>
z<n>.name <text> R zone <n> has been assigned the name <text>
a<n>.armed 1 R area <n> is armed
W arm area <n>
0 R area <n> is disarmed
W disarm area <n>
force W force arm area <n>
a<n>.alarm 1 R area <n> is in alarm
0 R area <n> is not in alarm
a<n>.open 1 R area <n> has open zones
0 R area <n> has no open zones
a<n>.isolated 1 R area <n> has isolated zones
0 R area <n> has no isolated zones
a<n>.exit 1 R exit time is active on area <n>
0 R exit time is not active on area <n>
a<n>.entry 1 R entry time is active on area <n>
0 R entry time is not active on area <n>
a<n>.alarm.local 1 R local alarms are active on area <n>
0 R no local alarm is active on area <n>
a<n>.warning 1 R console warning is active on area <n>
0 R console warning is not active on area <n>
z<n>.state1[Note] tamper R tamper active on zone <n>
alarm R alarm active on zone <n>
closed R zone <n> closed
night R night holdup active on zone <n>
local R local alarm active on zone <n>
isolated R zone <n> isolated
z<n>.state2[Note] short R zone <n> in short circuit
open R zone <n> open
closed R zone <n> closed
active R zone <n> active
masked R zone <n> masked
z<n>.isolated 1 W isolate zone <n>
0 W de-isolate zone <n>
z<n>.alarm reset W reset alarms on zone <n>
o<n>.active 1 R output <n> is active
W activate output <n>
0 R output <n> is not active
W deactivate output <n>
o<n>.inverted 1 R output <n> is inverted
0 R output <n> is not inverted
ras<n>.offline 1 R RAS <n> is offline
0 R RAS <n> is online
ras<n>.tamper 1 R RAS <n> is tampered
0 R RAS <n> is not tampered
ras<n>.isolated 1 R RAS <n> is isolated
0 R RAS <n> is not isolated
ras<n>.inhibited 1 R RAS <n> is inhibited
0 R RAS <n> is not inhibited
dgp<n>.offline 1 R DGP <n> is offline
0 R DGP <n> is online
dgp<n>.isolated 1 R DGP <n> is isolated
0 R DGP <n> is not isolated
dgp<n>.inhibited 1 R DGP <n> is inhibited
0 R DGP <n> is not inhibited
dgp<n>.battery.missing 1 R battery missing on DGP <n>
0 R battery ok on DGP <n>
dgp<n>.battery.low 1 R battery low on DGP <n>
0 R battery ok on DGP <n>
dgp<n>.battery.test 1 R battery test active on DGP <n>
0 R no battery test active on DGP <n>
dgp<n>.battery.test.fail 1 R battery test failed on DGP <n>
0 R battery test ok on DGP <n>
dgp<n>.mains.fail 1 R mains failure on DGP <n>
0 R mains ok on DGP <n>
dgp<n>.fuse.fail 1 R fuse failure on DGP <n>
0 R fuses ok on DGP <n>
dgp<n>.siren.fail 1 R siren failure on DGP <n>
0 R siren ok on DGP <n>
dgp<n>.tamper 1 R DGP <n> is tampered
0 R DGP <n> is not tampered

Note
The value of a zone status (datapoints z<n>.state1 and z<n>.state2) depends on the configuration of the zone typology.

User Interface

Ats Object

The user interface for the Aritech ATS multi-area intrusion detection system:

Ats UI Object 1.png Ats UI Object 2.png Ats UI Object 3.png

The Ats object is listed in the Project Editor’s new object list only when at least one Aritech ATS I/O Server is defined.


Parameters

  • server id: the server ID
  • position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(ats <server id>; <position>)

E.g.

(ats serverid; x10y20)

UISET Actions

ID Attribute Set to
log value latest security log lines (as many as specified by the 'logsize' option)
log0 value latest line of the security log when a new entry is added, set back to blank after a short period
a<n>.name value name assigned to area <n>
z<n>.name value name assigned to zone <n>
connection.label visible true when datapoint connection = offline
false when datapoint connection = online
<datapoint_id>.label.1 visible true when datapoint with ID <datapoint_id> has value '1'
false when datapoint with ID <datapoint_id> has value '0'
<datapoint_id>.label.0 visible true when datapoint with ID <datapoint_id> has value '0'
false when datapoint with ID <datapoint_id> has value '1'


USER Commands

Name Param Action
armed 1 arm all active areas
0 disarm all active areas
alarm reset reset system alarms
a<n>.armed 1 arm area <n>
0 disarm area <n>
force force arm area <n>
z<n>.isolated 1 isolate zone <n>
0 de-isolate zone <n>
z<n>.alarm reset reset alarms on zone <n>
o<n>.active 1 activate output <n>
0 deactivate output <n>