Hephais

The SD3 HEPHAIS 1600 is a multi-zones fire panel. The integration with HSYCO can be accomplished via a standard Modbus RTU slave interface. This I/O Server requires HEPHAIS 1600 with protocol modbus JBUS V0.13.

Modbus Connections

The HEPHAIS 1600 has a Modbus interface.

• Modbus address: 1 (can be set to 1 - 247)

• RS-422 parameters:

Baud rate	9600
Data bits	8
Stop bit	1
Parity	none
Flow control	none

Refer to the HEPHAIS 1600 manuals for installation, wiring and power supply requirements.

The modbus wires terminal is the “Block 11”. Modbus type is RS-422/JBUS (IN+/OUT+, IN-/OUT-, GND).

The Modbus-TCP/IP gateway used for the connection must support RS-422/JBUS.

HSYCO Configuration

You can define and connect more than one HEPHAIS panel on the same Modbus bus gateway or through different gateways.

Add an Hephais I/O Server in the I/O Servers section of the Settings and set its parameters:

Communication

• Comm ID: select a MODBUSTCP I/O server if using a Modbus gateway, or the serial port id when using a direct RS-485 port with HSYCO acting as Modbus RTU master.

High Availability

• Shutdown when inactive: defaults to false.

Options

ID	Default	Values	Description
gui	true	true	enable support for the UI object, UISET actions and USER commands
		false	disable UI support
startupevents	false	true	generate IO events also during the driver’s start-up phase
		false	start generating events only after HSYCO is aligned with the current status of the system
address	1	1...247	the panel's Modbus address
pollinterval	3	n > 0	the data acquisition interval, in seconds
maxpoint	m4.l2.200	point id	id of the highest point used on the panel. The number after ‘m’ represents the number of the module, the number after ‘l’ represents the loop number of the module and the last number is the address of the point within the loop. Acceptable values range from “m1.l1.1” to “m9.l2.200”
hysteresis	0	<n>	if different than zero, the datapoints’ values are checked <n> times before being set. Setting this option to a value different from zero will decrease the responsiveness of the driver

hephais.ini

The hephais.ini file is a specific configuration file located in the root directory. Here you can define the names of the users so that they will be automatically added to the user interface. Add a new line for each user using this format:

<io_server_id>.m<m>.l<l>.<addr>.name = <name>

Add a new line to specify the zone the point belongs using this format: <io_server_id>.m<m>.l<l>.<addr>.zone = <name>

Add a new line to define the name of a zone using this format: <io_server_id>.z<n>.name = <name>

For instance:

fire.m1.l1.1.name = Entrance
fire.m1.l1.1.zone = 1
fire.m1.l1.2.name = Corridor
fire.m1.l1.2.zone = 2

fire.z1.name = Zone 1
fire.z2.name = Zone 2

Datapoints

ID	Value	R/W	Description
connection	online	R	connection established
	offline	R	HSYCO can't connect to the panel
alarm	1	R	fire panel in alarm
	0	R	no alarm
fault	1	R	fire panel fault
	0	R	no fault
oos	1	R	at least one point out of service
	0	R	no point out of service
test	1	R	at least one zone in test mode
	0	R	no zone in test mode
error.sys	1	R	system fault
	0	R	no system fault
prealarm	1	R	fire panel in pre-alarm
	0	R	no pre-alarm
alarm.tec	1	R	fire panel in technical alarm
	0	R	no technical alarm
sound	1	R	H.S. speaker active
	0	R	H.S. speaker not active
error.com	1	R	fire panel communication error
	0	R	no fire panel communication error
error.battery	1	R	fire panel battery error
	0	R	no fire panel battery error
error.sector	1	R	fire panel sector fault
	0	R	no fire panel sector fault
z<n>.name	<text>	R	name assigned to zone <n>
z<n>.alarm	1	R	fire panel in alarm
	0	R	no alarm
z<n>.oos	1	R	fire panel in alarm
	0	R	no alarm
z<n>.fault	1	R	fire panel in alarm
	0	R	no alarm
z<n>.test	1	R	fire panel in alarm
	0	R	no alarm
m<m>.l<l>.<n>.name	<text>	R	name assigned to point P of module <m> in loop <l>
m<m>.l<l>.<n>.oos	1	R	point <n> of module <m> in loop <l> out of service
	0	R	point <n> of module <m> in loop <l> not out of service
m<m>.l<l>.<n>.alarm	1	R	point <n> of module <m> in loop <l> in alarm
	0	R	point <n> of module <m> in loop <l> not in alarm
m<m>.l<l>.<n>.fault	1	R	point <n> of module <m> in loop <l> out of fault
	0	R	point <n> of module <m> in loop <l> out not in fault
m<m>.l<l>.<n>.alarm.test	1	R	point <n> of module <m> in loop <l> alarm test
	0	R	point <n> of module <m> in loop <l> not in alarm test

User Interface

Hephais Object

The user interface for the Hephais I/O Server:

The (hephais) object is listed in the Project Editor’s new object list only when at least one Hephais I/O Server is defined

Parameters

• server id: the server ID. Supports Redirect variables
• position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(hephais <server id>; <position>)

E.g.

(hephais heph; r1c1)

UISET Actions

ID	Attribute	Set to
connection.label.online	visible	true	when datapoint connection = online
		false	when datapoint connection = offline
connection.label.offline	visible	true	when datapoint connection = offline
		false	when datapoint connection = online
alarm.label.1	visible	true	when the fire panel is in alarm
		false	when the fire panel is not in alarm
alarm.label.0	visible	true	when the fire panel is not in alarm
		false	when the fire panel is in alarm
fault.label.1	visible	true	when the fire panel is in fault
		false	when the fire panel is not in fault
fault.label.0	visible	true	when the fire panel is not in fault
		false	when the fire panel is in fault
oos.label.1	visible	true	when at least one point is out of service
		false	when no one of the points is out of service
oos.label.0	visible	true	when no one of the points is out of service
		false	when at least one point is out of service
test.label.1	visible	true	when at least one zone is in test mode
		false	when there aren't zones in test mode
test.label.0	visible	true	when there aren't zones in test mode
		false	when at least one zone is in test mode
error.sys.label.1	visible	true	when there is a system fault
		false	when there is not a system fault
error.sys.label.0	visible	true	when there is not a system fault
		false	when there is a system fault
prealarm.label.1	visible	true	when the fire panel is in pre-alarm
		false	when the fire panel is not in pre-alarm
prealarm.label.0	visible	true	when the fire panel is not in pre-alarm
		false	when the fire panel is in pre-alarm
alarm.tec.label.1	visible	true	when the fire panel is in technical alarm
		false	when the fire panel is not in technical alarm
alarm.tec.label.0	visible	true	when the fire panel is not in technical alarm
		false	when the fire panel is in technical alarm
sound.label.1	visible	true	when H.S. sound speaker is active
		false	when H.S. sound speaker is not active
sound.label.0	visible	true	when H.S. sound speaker is not active
		false	when H.S. sound speaker is active
error.com.label.1	visible	true	when there is a communication fault
		false	when there is not a communication fault
error.com.label.0	visible	true	when there is not a communication fault
		false	when there is a communication fault
error.battery.label.1	visible	true	when there is a battery fault
		false	when there is not a battery fault
error.battery.label.0	visible	true	when there is not a battery fault
		false	when there is a battery fault
error.sector.label.1	visible	true	when there is a sector error
		false	when there is not a sector error
error.sector.label.0	visible	true	when there is not a sector error
		false	when there is a sector error
z<n>.alarm.label.1	visible	true	when the zone <n> is in alarm
		false	when the zone <n> is not in alarm
z<n>.alarm.label.0	visible	true	when the zone <n> is not in alarm
		false	when the zone <n> is in alarm
z<n>.oos.label.1	visible	true	when the zone <n> is out of service
		false	when the zone <n> is not out of service
z<n>.oos.label.0	visible	true	when the zone <n> is not out of service
		false	when the zone <n> is out of service
z<n>.fault.label.1	visible	true	when the zone <n> is in fault
		false	when the zone <n> is not in fault
z<n>.fault.label.0	visible	true	when the zone <n> is not in fault
		false	when the zone <n> is in fault
z<n>.test.label.1	visible	true	when the zone <n> is in test
		false	when the zone <n> is not in test
z<n>.test.label.0	visible	true	when the zone <n> is not in test
		false	when the zone <n> is in test

Release Notes

3.3.0

• initial release

---

SD3 and HEPHAIS are registered trademarks owned by SD3.