IonoPiMax

From HSYCO
Jump to navigation Jump to search

Iono Pi Max is an extremely versatile industrial server with a huge variety of Input/Output lines and standard communication interfaces, all routed to the incredibly powerful quad-core processor of the Raspberry Pi.

iono Pi

This driver provides support for a local installation of HSYCO on Iono Pi Max itself.

HSYCO Configuration

Add a IONO Pi Max I/O Server in the I/O Servers section of the Settings and set its parameters:

Note that the IONO Pi Max I/O Server doesn't count in the I/O servers license total, so you don't need an extra I/O Server license to use IONO Pi Max with HSYCO.


Communication

  • IP Address: the IP address assigned to Iono Pi, leave blank for a local installation;
  • Port: TCP port configured on Iono Pi, leave blank for a local installation;

High Availability

  • Shutdown when inactive: defaults to false.

Options

ID Default Values Description
startupevents true true generate IO events also during the driver’s start-up phase
false start generating events only after HSYCO is aligned with the current status of the system
wiegandbits false true the wiegand datapoints report bits count and data value
false the wiegand datapoints report the data value only
https false true use HTTPS to communicate with a remote Iono Pi
false use HTTP to communicate with a remote Iono Pi
readinterval 2000 <ms> For local installation only. Interval, in milliseconds, between subsequent readings of analog inputs and 1-Wire devices. If the value is set below 2000 (i.e. less than 2 seconds) the specified interval is only applied to analog inputs; 1-Wire devices will be polled with a 2 seconds interval. Set to 0 to disable analog inputs polling
analogminvariation 100 <mV> For local installation only. Minimum voltage variation (in millivolts) to be measured on analog inputs, after an event has been triggered, for a new one to occur. Defaults to 0
digitalinputs true true For local installation only. Enable digital inputs monitoring
false For local installation only. Disable digital inputs monitoring
digitaldebounce 30 <ms> For local installation only. Time, in milliseconds, required for digital inputs to maintain a value, after a variation, before an event is triggered
wiegand1 false true For local installation only. Enable and monitor Wiegand interface 1
false For local installation only. Disable Wiegand interface 1
wiegand2 false true For local installation only. Enable and monitor Wiegand interface 2
false For local installation only. Disable Wiegand interface 2
onewirebus true For local installation only. Enable reading of the 1-Wire bus devices connected on TTL1
false For local installation only. Disable reading of the 1-Wire bus devices connected on TTL1
If not specified the monitoring will be enabled if the 1-Wire interface is enabled in the Raspberry Pi OS configuration

Datapoints

ID Value R/W Description
connection online R connection established
offline R HSYCO can't connect to the device
driverstate init R Sfera driver is initializing
quit R Sfera driver quit
running R Sfera driver is running (normal state)
led 0 R LED L1 is off
W turn LED L1 off
1 R LED L1 is on
W turn LED L1 on
o<1-4> 0 R relay <1-4> is off
W switch off relay <1-4>
1 R relay <1-4> is on
W switch on relay <1-4>
oc<1-3> 0 R open collector output <1-3> is off (not grounded)
W switch off open collector output <1-3>
1 R open collector output <1-3> is on (grounded)
W switch on open collector output <1-3>
di<1-6> 0 R digital input <1-6> is low
1 R digital input <1-6> is high
ai<1-4> <val> R analog input <1-4> is reading a voltage equal to <val> (in Volts)
wiegand.<1-2> <val> R if option "wiegandbits" set to false. Value as an unsigned integer in base 16 (hex) read on the specified Wiegand interface (e.g. "2c646a2")
<bits>/<val> R if option "wiegandbits" set to true. Number of bits and value (hex) read on the specified Wiegand interface (e.g. "26/2c646a2")
onewire.bus.<id> <val> R 1-Wire device <id> value

User Interface

To control a digital output (O1 ... O4, OC1 ... OC3, LED), add a button or a buttonicon object to your project page and set its address field to the corresponding datapoint:

IonoPi UI Button.png

Release Notes

3.7.0

  • initial release


Iono Pi Max is a registered trademark of Sfera Labs Srl