Difference between revisions of "Audio and Public Announcement"
| Line 84: | Line 84: | ||
Voice names in HSYCO are the same names you see in this panel. | Voice names in HSYCO are the same names you see in this panel. | ||
| − | {{note| | + | {{note|With OS X 10.9, the text-to-speech engine needs to be executed using an operating system account with voices properly defined in the user's Preferences panel. Because of this, |
HSYCO needs to know the user name to play a specific voice, and you should prefix the voice name with the user id and a colon character, like <b>user_id:voice</b> Text-to-speech will not work otherwise.}} | HSYCO needs to know the user name to play a specific voice, and you should prefix the voice name with the user id and a colon character, like <b>user_id:voice</b> Text-to-speech will not work otherwise.}} | ||
| + | |||
| + | |||
| + | {{note|The text-to-speech engine works only if a user's desktop is open. It is recommended to configure OSX with automatic login.}} | ||
| + | |||
The AudioServerSpeed and AudioServerQuality configuration parameters are supported. | The AudioServerSpeed and AudioServerQuality configuration parameters are supported. | ||
Revision as of 17:47, 11 September 2015
HSYCO can play audio for public announcement, as pre-recorded files or using a text-to-speech engine that converts text to audio. Audio can be sent to the Web browser, the server’s audio line out connector, the internal speaker or audio out line of Axis cameras, SNOM's phones or PA devices, and I/O servers with audio capabilities.
When playing a pre-recorded audio file, the file format should be supported by the audio destination you are using.
| Destination | Audio Formats |
| speaker | most of the audio formats that are supported by Linux or Mac OS X should work |
| web | use an audio format that is supported by the target Web browser
(only the most recent versions of Chrome and Firefox are supported) |
| axis | use uLaw, 8 KHz, 8 bit, mono, WAV files |
| snom | use uLaw, 8 KHz, 8 bit, mono, WAV files |
| io | use an audio format that is supported by the target I/O server |
The Text-to-Speech Engine
HSYCO uses different text-to-speech engines on Linux and Mac OS X.
On Linux, the default engine is eSpeak, with the possibility to use the optional Acapela engine that offers a wide selection of very high quality voices.
Go to http://espeak.sourceforge.net/ for more information about the eSpeak software.
On Mac OS X, HSYCO uses the integrated text-to-speech service and all its voices.
eSpeak
When using eSpeak, set the voice name to any of its supported voices.
Some voices are listed in the following table, but check the on-line documentation for the complete list.
| Voice | Description |
| voice:en | English |
| voice:en-us | American English |
| voice:it | Italian |
| voice:fr | French |
The AudioServerSpeed and AudioServerVolume configuration parameters are supported.
The AudioServerSpeed default is 100: higher numbers increase the speech speed.
The AudioServerVolume default is 10, and should be set between 0 and 20, where 20 generates an audio file with the greatest possible amplitude.
Acapela
When using Acapela, it is mandatory to set the AudioServerTTS configuration parameter to acapela:
AudioServerTTS = acapela
Moreover, set the voice name to any of its installed voices.
When playing to the SNOM phones, use 8k and 22k voices.
When playing to Axis cameras, use 8kmu voices.
Mac OS X
HSYCO supports text-to-speech on Mac OS X 10.7 or later, using the integrated text-to-speech engine.
You can install additional voices through the speech system preferences panel.
Voice names in HSYCO are the same names you see in this panel.
The AudioServerSpeed and AudioServerQuality configuration parameters are supported.
AudioServerSpeed is a positive number that represents speech rate, in words per minute.
AudioServerQuality sets the audio converter quality level between 0 (lowest) and 127 (highest).
