Paradox

PARADOX® EVO48 and EVO192 are advanced, multi-area security systems integrated with a variety of wired and wireless sensors. The EVO48 supports up to 48 zones in 4 areas (partitions), while the EVO192 supports 192 zones in 8 areas. Both units support programmable outputs (PGM) and virtual inputs. The Paradox EVO driver in HSYCO supports the integration of more than one EVO unit within the same HSYCO interface. The integration with HSYCO can be accomplished via direct control through the RS-232 port on the PRT3 Integration Module.

Communication

Employ a DE-9 (often called DB-9) male-female RS-232 straight cable to connect the PRT3 to the serial port on HSYCO SERVER.

RS-232 parameters:

Baud rate	same as defined on the PRT3 (default 9600)
Data bits	8
Stop bit	1
Parity	no parity
Flow control	none

Using the software Winload (default user: Master; default password: 1234) set the PRT3 speed to the appropriate rate setting options 2 and 3 of section 016. You can use any of the speeds that the PRT3 supports. 9600 or higher is recommended. Enable serial communication and home automation protocol (Ascii protocol).

HSYCO Configuration

Options

ID	Default	Values	Description
gui	true	true	enable support for the UI object, UISET actions and USER commands
		false	disable UI support
language	system language	en	language of log and display messages. Supported values are it and en
		it
zoneactivitylog	false	true	logs the open/close status of zones in the log page and security.log files
		false	disable zone status log
maxzone	0	0 ≥ n ≤ 192	force zones status detect and data points initialization at startup (zones data points are initialized with events disabled) for zones 1 to maxzone value
areanamelog	true	true	adds the area name to all log messages
		false	remove the area name (if only one area is used, having the area name in the logs could be useless)
code		code	the user code to be used when sending IO commands to the EVO, if code is not explicitly set in the command
logsize	50	n ≥ 0	the number of log lines to display in the UI object

Datapoints

ID	Value	R/W	Description
connection	online	R	connection established
	offline	R	HSYCO can't connect to the panel
area.<n>	arm	W	arm area <n> using default code
	disarm	W	disarm area <n> using default code
	force	W	arm area <n> using default code
	stay	W	arm area <n> using default code
	instant	W	arm area <n> using default code
	arm.<c>	W	arm area <n> using code <c>
	disarm.<c>	W	disarm area <n> using code <c>
	force.<c>	W	forced arm area <n> using code <c>
	stay.<c>	W	stay arm area <n> using code <c>
	instant.<c>	W	instant arm area <n> using code <c>
area.<n>.mode	disarmed	R	the area is disarmed
	armed	R	the area is armed
	forced	R	the area is armed (force mode)
	stay	R	the area is armed (stay mode)
	instant	R	the area is armed (instant mode)
area.<n>.status	alarm	R	area in alarm
	strobe	R	area in strobe (silent alarm)
	reset	R	area alarm end
area.<n>.trouble	trouble	R	general trouble in the area
	reset	R	trouble end
zone.<n>.status	closed	R	zone is closed
	open	R	zone is open
	tamper	R	zone tampered
	fireloop	R	fire loop trouble
zone.<n>.alarm	alarm	R	zone alarm
	fire	R	zone fire alarm
	reset	R	alarm end
zone.<n>.trouble	radio	R	zone radio supervision lost
	battery	R	zone low battery warning
	reset	R	zone trouble end
trouble	online	R	connection established
	offline	R	connection failed
pgm.<n>	on	R	the PGM is activated
	off	R	the PGM is deactivated
input.<n>	open	RW	the virtual input is open
	0	W	set virtual input to open
	closed	RW	set virtual input to closed
	1	W	set virtual input to open