Difference between revisions of "Hidedgesolo"

From HSYCO
Jump to navigation Jump to search
 
(20 intermediate revisions by 5 users not shown)
Line 1: Line 1:
−
The HID Edge solo ESR40, ESRP40, ES400 are single-door IP access control solution. This driver allows the integration of HID Edge Solo devices by using a TCP/IP connection. More than one device can be controlled at the same time.
+
The [http://www.hidglobal.com HID Edge Solo] '''ESR40, ESRP40, ES400''' are single-door IP access control solutions.  
  
−
[[Category:I/O Server]]
+
This I/O Server allows the integration of HID Edge Solo devices by using a TCP/IP connection.
  
−
== Communication ==
+
More than one device can be controlled at the same time.
  
−
An IP address must be assigned to the HID Edge Solo.
+
[[Category:I/O Server]]
  
−
== HID Edge Solo configuration ==
+
== HID Edge Solo Configuration ==
  
 
The HID Edge Solo can be connected to a POE switch or to a normal ethernet switch. In this case the power supply must be provided with an external adapter.
 
The HID Edge Solo can be connected to a POE switch or to a normal ethernet switch. In this case the power supply must be provided with an external adapter.
−
First of all, assign an IP address to the Edge Solo, then it’s mandatory to disable the SSL/TLS encryption in the installer settings interface.
+
First of all, assign a static IP address to the Edge Solo, then it’s mandatory to disable the SSL/TLS encryption in the installer settings interface.
  
 
[[File:hidedgesolo1.png]]
 
[[File:hidedgesolo1.png]]
 +
 +
== HSYCO Configuration ==
 +
Add an HIDEDGESOLO I/O Server in the [[Settings#I/O Servers|I/O Servers section of the Settings]] and set its parameters:
 +
 +
=== Communication ===
 +
*'''IP Address''': IP address configured on the device
 +
*'''IP Port''': TCP/IP port to use, leave blank for default port 80.
 +
 +
=== Authentication ===
 +
*'''User''': username set in the installer settings
 +
*'''Password''': password set in the installer settings.
 +
 +
=== High Availability ===
 +
*'''Shutdown when inactive''': defaults to true.
  
 
== Datapoints ==
 
== Datapoints ==
 +
 +
If two readers are connected to the Edge Solo controller, the reader specific data points have a 0. or 1. prefix to identify each reader.
  
 
{| class="wikitable"
 
{| class="wikitable"
Line 172: Line 188:
 
|door held
 
|door held
 
|-
 
|-
−
|rowspan="2" |state.alarm.door.held
+
|rowspan="2" |state.alarm.door.forced
 
|unset
 
|unset
 
|R
 
|R
Line 179: Line 195:
 
|set
 
|set
 
|R
 
|R
−
|door held
+
|door forced
 +
|-
 +
|state.name
 +
|<name>
 +
|R
 +
|the door's name
 
|-
 
|-
−
|rowspan="2" |state.alarm.door.forced
+
|rowspan="2" |state.relay
 
|unset
 
|unset
 
|R
 
|R
−
|normal conditions
+
|door relay closed
 
|-
 
|-
 
|set
 
|set
 
|R
 
|R
−
|door forced
+
|door relay open
 
|-
 
|-
−
|rowspan="2" |state.relay
+
|rowspan="2" |state.relay.alert
 
|unset
 
|unset
 
|R
 
|R
−
|door relay closed
+
|alert relay not active
 
|-
 
|-
 
|set
 
|set
 
|R
 
|R
−
|door relay open
+
|alert relay active
 
|-
 
|-
 
|rowspan="2" |state.relay.aux
 
|rowspan="2" |state.relay.aux
 
|unset
 
|unset
 
|R
 
|R
−
|the device is not in alarm state
+
|aux relay not active
 
|-
 
|-
 
|set
 
|set
 
|R
 
|R
−
|the device is in alarm state
+
|aux relay active
 
|-
 
|-
 
|command.access
 
|command.access
Line 228: Line 249:
 
|}
 
|}
  
−
== Examples ==
+
== Release Notes ==
−
 
+
=== 3.6.0 ===
−
A valid pin is digit on the Wiegand keyboard of the EDGE SOLO. Here’s the HSYCO log:
+
*added support for firmware version 2.0
−
<pre>
 
−
IO MONITOR EVENT: hid1.state.relay = unset
 
−
IO MONITOR FORCED: hid1.access.granted = Gaffuri
 
−
IO MONITOR EVENT: hid1.state.relay = set
 
−
IO MONITOR EVENT: hid1.state.relay = unset
 
−
</pre>
 
−
 
 
−
The relay is set, the access is granted for the user. They relay is set for a time specified in the EDGE SOLO settings.
 
−
 
 
−
Access granted from a user button. Here’s the HSYCO log:
 
−
<pre>
 
−
WEB USER COMMAND [hid1]: grant [OK]
 
−
IO MONITOR EVENT: command.access = grant
 
−
IO MONITOR EVENT: hid1.state.relay = set
 
−
IO MONITOR FORCED: hid1.access.granted.manual = true
 
−
IO MONITOR EVENT: hid1.state.relay = unset
 
−
</pre>
 
−
 
 
−
After the button is pressed the relay is set. The manuale access granted is reported in the log.
 
−
 
 
−
Door forced. Here’s the HSYCO log:
 
−
<pre>
 
−
IO MONITOR FORCED: hid1.alarm.door.forced = 1
 
−
IO MONITOR EVENT: hid1.state.alarm.door.forced = set
 
−
IO MONITOR EVENT: hid1.state.relay.aux = set
 
−
IO MONITOR EVENT: hid1.state.relay.alert = set
 
−
</pre>
 
  
−
To grant an access using a user button, open the Project Editor and create a new user button. Specify the following parameters:
+
=== 3.4.0 ===
 +
*added support for two readers door controller
  
 +
=== 3.0.0 ===
 +
*initial release
  
 +
----
  
−
Name e param are used to call a spacific line in the events.txt file:
 
−
io hid1.state.relay = set : UISET hid1.color = g
 
−
io hid1.state.relay = unset : UISET hid1.color = gr
 
−
user hid1=grant : io hid1.command.access=grant
 
  
−
where hid1 is the id of the I/O server. The button color changes according to the relay state.
+
''HID is a registered trademark of HID Global.''

Latest revision as of 09:11, 15 September 2022

The HID Edge Solo ESR40, ESRP40, ES400 are single-door IP access control solutions.

This I/O Server allows the integration of HID Edge Solo devices by using a TCP/IP connection.

More than one device can be controlled at the same time.

HID Edge Solo Configuration

The HID Edge Solo can be connected to a POE switch or to a normal ethernet switch. In this case the power supply must be provided with an external adapter. First of all, assign a static IP address to the Edge Solo, then it’s mandatory to disable the SSL/TLS encryption in the installer settings interface.

Hidedgesolo1.png

HSYCO Configuration

Add an HIDEDGESOLO I/O Server in the I/O Servers section of the Settings and set its parameters:

Communication

  • IP Address: IP address configured on the device
  • IP Port: TCP/IP port to use, leave blank for default port 80.

Authentication

  • User: username set in the installer settings
  • Password: password set in the installer settings.

High Availability

  • Shutdown when inactive: defaults to true.

Datapoints

If two readers are connected to the Edge Solo controller, the reader specific data points have a 0. or 1. prefix to identify each reader.

ID Value R/W Description
connection online R connection established
offline R HSYCO can't connect to the panel
card.notfound <code> R badge <code> not found
pin.notfound <pin> R <pin> not found
access.granted <surname> R access granted to the user with surname <surname>
access.granted.extended <surname> R access granted extended to the user with surname <surname>
access.denied.schedule <surname> R access denied because badge/pin of the user <surname> was used outside scheduled time interval
access.denied.expired <surname> R access denied because badge/pin of the user <surname> is expired
card.notassigned <code> R access denied because the badge <code> is not assigned to an user.
access.denied.pin.expired <surname> R access denied because the pin assigned to the user <surname> is expired
alarm.acknowledged 0 R alarms reset
1 R normal conditions
door.lock.schedule false R normal conditions
true R door locked with a scheduled command
door.unlock.schedule false R normal conditions
true R door unlocked with a scheduled command
alarm.door.forced unset R normal conditions
set R door forced alarm
alarm.tamper unset R normal conditions
set R tamper alarm
access.granted.manual false R normal conditions
true R manual access granted
door.unlock false R normal conditions
true R door unlocked
state.alarm.tamper unset R normal conditions
set R tamper alarm
state.alarm.ac unset R normal conditions
set R power supply failure
state.alarm.battery unset R normal conditions
set R battery failure
state.alarm.door.held unset R normal conditions
set R door held
state.alarm.door.forced unset R normal conditions
set R door forced
state.name <name> R the door's name
state.relay unset R door relay closed
set R door relay open
state.relay.alert unset R alert relay not active
set R alert relay active
state.relay.aux unset R aux relay not active
set R aux relay active
command.access grant W grant the access
command.door lock W lock the door
unlock W unlock the door
command.alarm stop W alarms reset

Release Notes

3.6.0

  • added support for firmware version 2.0

3.4.0

  • added support for two readers door controller

3.0.0

  • initial release


HID is a registered trademark of HID Global.

Retrieved from "https://wiki.hsyco.com/3.8/index.php?title=Hidedgesolo&oldid=10759"