Dea Xensity
DEA XENSITY is a Point ID intrusion detection system using special piezoelectric sensors for the protection of doors, windows, glass surfaces, security grilles and walls. This driver is compatible with the following controllers: Xensity128, Xensity64, Xensity32. Make sure to install the latest available firmware.
Contents
Communication
DEA XENSITY panels can be connected via ethernet. A valid IP address must be assigned to the controller using the configuration software.
In case of multiple DEA XENSITY IO Servers running on the same HSYCO Server you must assign a different UDP port to each XENSITY driver
HSYCO Configuration
Add a XENSITY I/O Server in the I/O Servers section of the Settings and set its parameters:
Communication
- Address: IP address of the XENSITY controller (mandatory)
- Port: UDP port (mandatory)
High Availability
- Shutdown when inactive: defaults to false.
Options
| ID | Default | Values | Description |
|---|---|---|---|
| startupevents | false | true | generate IO events also during the driver’s start-up phase |
| false | start generating events only after HSYCO is aligned with the current status of the system | ||
| pollinterval | 1000 | n ≥ 0 | the data polling interval, in milliseconds. Shorter time improve the response of the system, but increase the load on the CPU of both HSYCO and the Xensity system |
Datapoints
| ID | Value | R/W | Description |
|---|---|---|---|
| connection | online | R | connection established |
| offline | R | HSYCO can't connect to the panel | |
| alarm | 0 | R | no alarms |
| 1 | R | at least one zone of this controller on alarm | |
| link.x16 | 0 | R | Connection with X16-ER16L is not stable |
| 1 | R | Connection with X16-ER16L is stable | |
| link.sens | 0 | R | Connection with sensors is not stable |
| 1 | R | Connection with sensors is stable | |
| bus.power | 0 | R | Bus sensors power supply not ok |
| 1 | R | Bus sensors power supply ok | |
| alarm.nf | 0 | R | panel in not in test mode |
| 1 | R | At least one alarm is active - not filtered- | |
| global.daynight | 0 | R | panel in day mode |
| 1 | R | panel is night mode | |
| global.mcpalarm | 0 | R | mcp alarm off |
| 1 | R | mcp alarm on | |
| global.sounder.delay.enabled | 0 | R | sounders delay disabled |
| 1 | R | sounders delay enabled | |
| global.sounder.delay.in.progress | 0 | R | sounders delay not in progress |
| 1 | R | sounders delay in progress | |
| global.sounder.outputs.activated | 0 | R | sounders outputs not active |
| 1 | R | sounders outputs active | |
| global.sounder.outputs.silenced | 0 | R | sounders outputs not silenced |
| 1 | R | sounders outputs silenced | |
| global.sounder.disabled | 0 | R | sounders are enabled |
| 1 | R | sounders are disabled | |
| global.sounder.override.time.elapsed | 0 | R | override sounders time is not elapsed |
| 1 | R | ovveride sounders time elapsed | |
| global.sounder.in.test | 0 | R | sounders not in test |
| 1 | R | sounders in test | |
| global.fire.routing.delay.enabled | 0 | R | fire routing delay not enabled |
| 1 | R | fire routing delay enabled | |
| global.fire.routing.delay.in.progress | 0 | R | fire routing delay not in progress |
| 1 | R | fire routing in progress | |
| global.fire.routing.ouputs.activated | 0 | R | fire routing outputs not activated |
| 1 | R | fire routing outputs activated | |
| global.fire.routing.ack | 0 | R | fire routing not in ack |
| 1 | R | fire routing ack | |
| global.fire.routing.disabled | 0 | R | fire routing enabled |
| 1 | R | fire routing disabled | |
| global.fire.routing.test.on | 0 | R | fire routing test is off |
| 1 | R | fire routing test on | |
| global.fire.routing.ext.delay.in.progress | 0 | R | fire routing ext delay not in progress |
| 1 | R | fire routing ext delay in progress | |
| node.<n>.loop.<l>.sensor.<s>.prealarm | 0 | R | not in prealarm |
| 1 | R | prealarm | |
| node.<n>.loop.<l>.sensor.<s>.alarm | 0 | R | not in alarm |
| 1 | R | alarm | |
| node.<n>.loop.<l>.sensor.<s>.fault | 0 | R | not in fault |
| 1 | R | fault | |
| node.<n>.loop.<l>.sensor.<s>.test | 0 | R | not in test |
| 1 | R | in test | |
| node.<n>.loop.<l>.sensor.<s>.dis | 0 | R | enabled |
| 1 | R | disabled | |
| node.<n>.loop.<l>.module.<s>.prealarm | 0 | R | not in prealarm |
| 1 | R | prealarm | |
| node.<n>.loop.<l>.module.<s>.alarm | 0 | R | not in alarm |
| 1 | R | alarm | |
| node.<n>.loop.<l>.module.<s>.fault | 0 | R | not in fault |
| 1 | R | fault | |
| node.<n>.loop.<l>.module.<s>.test | 0 | R | not in test |
| 1 | R | in test | |
| node.<n>.loop.<l>.module.<s>.dis | 0 | R | enabled |
| 1 | R | disabled |
Release Notes
3.7.0
- initial release
KILSEN is a registered trademark of UTC Climate, Controls & Security
