Difference between revisions of "Detnov"
Jump to navigation
Jump to search
| Line 361: | Line 361: | ||
|R | |R | ||
|the sounder <n> is active | |the sounder <n> is active | ||
| + | |- | ||
| + | |||
| + | |rowspan="2" |global.relay.fault | ||
| + | |0 | ||
| + | |R | ||
| + | |global relay fault is off | ||
| + | |- | ||
| + | |1 | ||
| + | |R | ||
| + | |global relay fault is on | ||
| + | |- | ||
| + | |||
| + | |rowspan="2" |global.relay.alarm | ||
| + | |0 | ||
| + | |R | ||
| + | |global relay alarm is off | ||
| + | |- | ||
| + | |1 | ||
| + | |R | ||
| + | |global relay alarm is on | ||
| + | |- | ||
| + | |||
| + | |global.faults.counter | ||
| + | |<n> | ||
| + | |R | ||
| + | |n is the number of global faults | ||
| + | |- | ||
| + | |||
| + | |global.alarms.counter | ||
| + | |<n> | ||
| + | |R | ||
| + | |n is the number of global alarms | ||
| + | |- | ||
| + | |||
| + | |rowspan="2" |loop.<n>.active | ||
| + | |0 | ||
| + | |R | ||
| + | |the loop <n> is not active | ||
| + | |- | ||
| + | |1 | ||
| + | |R | ||
| + | |the loop <n> is active | ||
| + | |- | ||
| + | |||
| + | |rowspan="2" |loop.<n>.shortopen.fault | ||
| + | |0 | ||
| + | |R | ||
| + | |the loop <n> is not in short or open fault | ||
| + | |- | ||
| + | |1 | ||
| + | |R | ||
| + | |the loop <n> is in short or open fault | ||
| + | |- | ||
| + | |||
| + | |rowspan="2" |loop.<n>.comm.fault | ||
| + | |0 | ||
| + | |R | ||
| + | |the loop <n> is not in communication fault | ||
| + | |- | ||
| + | |1 | ||
| + | |R | ||
| + | |the loop <n> is in communication fault | ||
|- | |- | ||
Revision as of 17:39, 28 December 2020
DETNOV are multi-area fire panels. The integration with HSYCO can be accomplished via a standard Modbus TCP/IP connection. This I/O server was developed following the MODBUS documentation MODBUS REGISTERS FOR DETNOV ADDRESSABLE SYSTEM VERSION 1.11 ENG
This driver has been tested on DETNOV CAD-150-2 panel. (Should be compatible with CAD 150-1, CAD 150-2, CAD 150-8, CAD 150-8+, CAD 150-4)
Contents
Communication
DETNOV panels can be connected via ethernet. A valid IP address must be assigned to the panel. MODBUS PROTOCOL must be enabled. Please refer to the manual for detailed instruction about MODBUS protocol configuration.
HSYCO Configuration
Add a DETNOV I/O Server in the I/O Servers section of the Settings and set its parameters:
Communication
- Address: IP address of the DETNOV panel
- Port: TCP/IP port for MODBUS communication (default 502)
High Availability
- Shutdown when inactive: defaults to false.
Options
| ID | Default | Values | Description |
|---|---|---|---|
| gui | true | true | enable support for the UI object, UISET actions and USER commands |
| false | disable UI support | ||
| startupevents | false | true | generate IO events also during the driver’s start-up phase |
| false | start generating events only after HSYCO is aligned with the current status of the system | ||
| unitid | 1 | > 0 | MODBUS unit ID of the DETNOV panel |
| pollingtime | 3000 | n >= 3000 | the data polling interval, in milliseconds. |
Datapoints
| ID | Value | R/W | Description |
|---|---|---|---|
| connection | online | R | connection established |
| offline | R | HSYCO can't connect to the panel | |
| reset | 1 | W | panel reset |
| mute | 1 | W | panel mute |
| sounderson | 1 | W | enable sounders |
| soundersoff | 1 | W | disable sounders |
| info.modbus.status | 0 | R | modbus is disconnected |
| 1 | R | modbus slave is connected | |
| info.panel.type | <n> | R | n=1,2 > CAD 150-1, CAD 150-2 n=4,8 > CAD 150-8, CAD 150-8+, CAD 150-4 |
| info.panel.version | <n> | R | n is the version of the panel |
| info.panel.network.version | <n> | R | n is the network version of the panel |
| info.panel.modbus.version | <n> | R | n is the modbus version of the panel |
| global.mute | 0 | R | mute is not active |
| 1 | R | mute is active | |
| global.sounders | 0 | R | sounders are not active |
| 1 | R | sounders are active | |
| global.sounders.silenced | 0 | R | sounders are not silenced |
| 1 | R | sounders are silenced | |
| intest.zone.exists | 0 | R | at least one zone is in test |
| 1 | R | no zones are in test | |
| disabled.zone.exists | 0 | R | at least one zone is disabled |
| 1 | R | no zones are disabled | |
| output.disabled | 0 | R | at least one output is disabled |
| 1 | R | no outputs are disabled | |
| sounders.disabled | 0 | R | at least one sounder is disabled |
| 1 | R | no sounders are disabled | |
| sounders.delayed | 0 | R | at least one sounder is delayed |
| 1 | R | no sounders are delayed | |
| global.panel.fault | 0 | R | panel has no fault |
| 1 | R | there is at least one fault in the panel | |
| global.power.fault | 0 | R | panel has no power fault |
| 1 | R | panel has a power fault | |
| global.pcb.fault | 0 | R | panel has no pcb fault |
| 1 | R | panel has a pcb fault | |
| global.loops.fault | 0 | R | the panel has no loop fault |
| 1 | R | panel has a loop fault | |
| global.device.fault | 0 | R | panel has no device fault |
| 1 | R | panel has a device fault | |
| global.alarm | 0 | R | the panel is not in alarm |
| 1 | R | panel is in alarm | |
| global.alarm.from.network | 0 | R | panel is not in network alarm |
| 1 | R | panel is in network alarm | |
| global.mcp.alarm | 0 | R | panel has no mcp alarm |
| 1 | R | panel has a mcp alarm | |
| global.main.supply.fault | 0 | R | panel has no main supply fault |
| 1 | R | panel has a main supply fault | |
| global.ground.fault | 0 | R | panel has no global ground fault |
| 1 | R | panel has a global ground fault | |
| global.sounder<n>.short.cut | 0 | R | the sounder <n> is not in short cut |
| 1 | R | the sounder <n> is in short cut | |
| global.sounder<n>.quiescent | 0 | R | the sounder <n> is not quiescent |
| 1 | R | the sounder <n> is quiescent | |
| global.sounder<n>.short.fault | 0 | R | the sounder <n> is not in short fault |
| 1 | R | the sounder <n> is in short fault | |
| global.sounder<n>.sounders.on | 0 | R | the sounder <n> is not active |
| 1 | R | the sounder <n> is active | |
| global.relay.fault | 0 | R | global relay fault is off |
| 1 | R | global relay fault is on | |
| global.relay.alarm | 0 | R | global relay alarm is off |
| 1 | R | global relay alarm is on | |
| global.faults.counter | <n> | R | n is the number of global faults |
| global.alarms.counter | <n> | R | n is the number of global alarms |
| loop.<n>.active | 0 | R | the loop <n> is not active |
| 1 | R | the loop <n> is active | |
| loop.<n>.shortopen.fault | 0 | R | the loop <n> is not in short or open fault |
| 1 | R | the loop <n> is in short or open fault | |
| loop.<n>.comm.fault | 0 | R | the loop <n> is not in communication fault |
| 1 | R | the loop <n> is in communication fault |
Release Notes
3.8.0
- initial release
