Lares4

From HSYCO
Jump to navigation Jump to search

The KSENIA lares 4.0 is a multi-area security system. The I/O Server has been tested on unit with firmware version 1.72.2 and web server version 1.32.7. Actually this driver runs only in HTTP mode (port 80 is set by default).


Configuration from Ksenia cloud

You must firstly configure your panel in the web app at the following address https://<panel_ip_addrss> (the panel starts in DHCP mode so you must find the relative IP address assigned). In the web app, select your panel and log into it with installer privileges, then go to settings. In settings, disable DHCP mode and set a static ip address, then disable HTTPS connection (you must select non-secure HTTP connection with port 80). When you have finished save your configuration. In alternative, you can configure your panel passing by Ksenia SecureWeb cloud.

HSYCO Configuration

Add a LARES4 I/O Server in the I/O Servers section of the Settings and set its parameters:

Communication

  • IP Address: host name or IP address of the panel
  • IP Port: leave it blank

Authentication

  • Password: pin to access the web server

High Availability

  • Shutdown when inactive: defaults to false.

Options

ID Default Values Description
startupevents false true generate IO events also during the driver’s start-up phase
false start generating events only after HSYCO is aligned with the current status of the system
pollinterval 1000 n > 1000 the data acquisition interval, in milliseconds
logsize 300 n ≥ 0 the number of log lines to display in the UI object
gui true true enable the UISET "visible" field for all partition zones
false disable the UISET "visible" field for all partition zones
maxpartitions 3 1≤n≤30 number of partitions that are configured in the security panel

Datapoints

ID Value R/W Description
connection online R connection established
offline R HSYCO can't connect to the panel
armed 1 W arm all partitions in the system
0 W disarm all partitions in the system
p<n>.desc <text> R description of partition <n>
p<n>.armed 0 R partition <n> is disarmed
W disarm partition <n>
1 R partition <n> is armed
W arm partition <n>
p<n>.alarm 0 R partition <n> not in alarm
1 R partition <n> in alarm
mem R partition <n> in alarm memory state
p<n>.tamper 0 R partition <n> not in tamper
1 R partition <n> in tamper
mem R partition <n> in tamper memory state
z<n>.desc <text> R description of zone <n>
z<n>.alarm 0 R zone <n> not in alarm
1 R zone <n> in alarm
z<n>.mask 0 R zone <n> not masked
1 R zone <n> masked
z<n>.tamper 0 R zone <n> not in tamper
1 R zone <n> in tamper
z<n>.error 0 R zone <n> not in error
1 R zone <n> in error
z<n>.bypass 0 R zone <n> is not bypassed
W unbypass zone <n>
1 R zone <n> is bypassed
W bypass zone <n>
o<n>.desc <text> R description of output <n>
o<n> 0 R output <n> is off
W turn off output <n>
1 R output n <n> is on
W turn on output <n>
voltage.low 0 R system voltage is ok
1 R system voltage is low
batt.low 0 R battery is ok
1 R battery is low
batt.fault 0 R battery is ok
1 R battery fault
pstn.fault 0 R pstn is ok
1 R pstn fault
credit.low 0 R credit is ok
1 R credit is low
system.fault 0 R system is ok
1 R system fault
mobile.fault 0 R mobile is ok
1 R mobile fault
s<n>.desc <text> R description of scenario <n>
s<n> 1 W trigger scenario <n>

User Interface

Lares4 Object

The user interface for the Lares4 multi-area intrusion detection system:

Lares4 UI Object 1.png Lares4 UI Object 2.png Lares4 UI Object 3.png

The first image shows the list of configured partitions. You can set the alarm for all the partitions, otherwise you can open a popup on a dedicated partition and set the alarm only for that one. The two icons on the top of the page represent in order: partition tamper (at least one partition is in tamper state), partition alarm (at least one partition is in alarm state).

The second image shows the popup associated to a zone; the four icons shown inside the popup represent in order: zone alarm, zone tamper, zone bypassed, zone fault. Inside the popup you can bypass/unbypass the selected zone.

The (lares4) object is listed in the Project Editor’s new object list only when at least one Lares4 I/O Server is defined

Parameters

  • server id: the server ID. Supports Redirect variables
  • position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(lares4 <server id>; <position>)

E.g.

(lares4 lares; x10y20)

UISET Actions

ID Attribute Set to
log value latest security log lines (as many as specified by the 'logsize' option)
log0 value latest security log (it will vanish after 5 seconds)
z<n>.tamper visible false zone n not in tampering
true zone n in tampering
z<n>.bypass visible false zone n not bypassed
true zone n bypassed
z<n>.alarm visible false zone n not in alarm
true zone n in alarm
z<n>.error visible false zone n not in error state
true zone n in error state
z<n>.mask visible false zone n not masked
true zone n masked

Log Files

If a Ksenia anti-intrusion unit is connected to HSYCO, the security.log file will be written in the same directories as the daily log files.

This file is never overwritten or deleted from HSYCO SERVER.

2018.02.20 16:59:28.516 - lares - 20/02/2018 16:56:36 - Disinserimento - Part 1 - U1
2018.02.20 17:00:24.527 - lares - 20/02/2018 16:57:36 - Inserimento - Part 1 - U1
2018.02.20 17:00:44.318 - lares - 20/02/2018 16:57:57 - Allarme - Zone 1
2018.02.20 17:00:49.241 - lares - 20/02/2018 16:57:58 - Ripristino - Zone 1
2018.02.20 17:00:54.043 - lares - 20/02/2018 16:58:06 - Disinserimento - Part 1 - U1
2018.02.20 17:01:18.905 - lares - 20/02/2018 16:58:29 - Fallita Comunicazione - Leonardo - Vocale GSM
2018.02.20 17:01:29.053 - lares - 20/02/2018 16:58:40 - Fallita Comunicazione - Leonardo - SMS

Other information about the Ksenia driver are stored in the message.log daily file.

Release Notes

3.8.0

  • initial version release


Ksenia is a registered trademark of Ksenia Security s.r.l.