Satel

From HSYCO
Jump to navigation Jump to search

The Satel INTEGRA series comprises a variety of multi-area security systems. The integration with HSYCO can be accomplished via direct control through Ethernet connection. The I/O Server complies with the protocol INT-RS v2.13 2015-03-19 and has been tested on firmware version 1.14 2015-12-15.

Satel Configuration

TODO

HSYCO Configuration

Add a SATEL I/O Server in the I/O Servers section of the Settings and set its parameters:

Communication

  • IP Address: host name or IP address of the panel
  • IP Port: TCP/IP port to use (as configured on the panel)

High Availability

  • Shutdown when inactive: defaults to true.

Options

ID Default Values Description
startupevents false true generate IO events also during the driver’s start-up phase
false start generating events only after HSYCO is aligned with the current status of the system
logsize 20 n ≥ 0 the number of log lines to display in the UI object
usercode <user_code> default user code to be used to send commands
maxzone 1 ≤ n ≤ 256 highest zone number configured on the panel
maxpartition 1 ≤ n ≤ 32 highest partition number configured on the panel
maxoutput 1 ≤ n ≤ 256 highest output number configured on the panel
maxdoor 1 ≤ n ≤ 64 highest door number configured on the panel


Datapoints

ID Value R/W Description
connection online R connection established
offline R HSYCO can't connect to the panel
armed 0 R all groups are disarmed
W disarm all groups
1 R the system is (partially) armed
W arm all groups
alarm 0 R the system is not in a alarm state
1 R the system is in a alarm state
tamper 0 R the system is not in a tamper state
1 R the system is in a tamper state
panel.tamper 0 R the panel is not tampered
1 R the panel is tampered
bell.tamper 0 R the bell is not tampered
1 R the bell is tampered
low.volts 0 R voltage ok
1 R low voltage detected
sounder 0 R the sounder is inactive
1 R the sounder is active
audio 0 R the audio signal of the panel is inactive
1 R the audio signal of the panel is active
strobe 0 R the strobe is inactive
1 R the strobe is active
mains.fail 0 R no mains fail
1 R mains fail
power.fail 0 R no power fail
1 R power fail
battery.fail 0 R no battery fail
1 R battery fail
fuse.1.fault 0 R fuse 1 is working
1 R fuse 1 in fault
fuse.2.fault 0 R fuse 2 is working
1 R fuse 2 in fault
fuse.3.fault 0 R fuse 3 is working
1 R fuse 3 in fault
line.fault 0 R communication line is working
1 R communication line in fault
c<n>.name <text> R the name of circuit <n> is set to <text>
g<n>.name <text> R the name of group <n> is set to <text>
g<n>.armed 0 R group <n> is disarmed
W disarm group <n>
1 R group <n> is armed
W arm group <n>
c<n>.alarm 0 R circuit <n> is not in alarm state
1 R circuit <n> is in alarm state
c<n>.tamper.alarm 0 R circuit <n> is not in tamper alarm
1 R circuit <n> is in tamper alarm
c<n>.open 0 R circuit <n> is closed
1 R circuit <n> is open
c<n>.tamper 0 R circuit <n> is not tampered
1 R circuit <n> is tampered
c<n>.fault 0 R circuit <n> is working properly
1 R circuit <n> is faulty
c<n>.bypassed 0 R circuit <n> is not bypassed
W unbypass circuit <n>
1 R circuit <n> is bypassed
W bypass circuit <n>
c<n>.isolated 0 R circuit <n> is not isolated
W un-isolate circuit <n>
1 R circuit <n> is isolated
W isolate circuit <n>
c<n>.soaked 0 R circuit <n> is not soaked
W un-soak circuit <n>
1 R circuit <n> is soaked
W soak circuit <n>
c<n>.status[Note 1] <status_values> R the status of circuit <n> is set to the reported values
c<n>.attributes[Note 1] <attributes_values> R the attributes of circuit <n> are set to the reported values
c<n>.resistance[Note 1] <value> R the measured resistance on circuit <n> is <value> ohm
>20k R the measured resistance on circuit <n> is greater than 20 K-ohm
k<n>.tamper 0 R keypad <n> is not tampered
1 R keypad <n> is tampered
k<n>.fault 0 R keypad <n> is working properly
1 R keypad <n> is faulty
logon.<n> <user_num> R user with number <user_num> logged in from keypad <n>
error R wrong pin entered in keypad <n>
system reset W reset alarms