Daikinrc

The DAIKINRC I/O Server is compatible with the Daikin room air conditioner series CTXM, ATXM and FTXM units that can be fitted with the Daikin wireless LAN adapter (BRP06xxx; versions BRP069C4x are not supported) and are supported by the Daikin Controller iOS and Android app.

A single DAIKINRC I/O Server controls all the devices connected to the local network.

Daikin Configuration and Discovery

All units must be connected to the same LAN of the HSYCO Server. When the DAIKINRC I/O Server starts, and then periodically every 30 to 60 seconds, a discovery request is sent to the LAN. New units responding to the discovery request will start to be polled by the I/O Server and become online.

HSYCO Configuration

Add a DAIKINRC I/O Server in the I/O Servers section of the Settings and set its parameters.

 A single DAIKINRC I/O Server discovers and controls all units connected to the LAN.

Communication

As the I/O Server automatically discovers all units connected to the local network, no connection parameters are required.

High Availability

• Shutdown when inactive: defaults to true.

Options

ID	Default	Values	Description
pollinterval	5	1 <= n <= 30	the status poll interval, in seconds

Datapoints

In the following table, replace <unit> with the name assigned to a room air conditioner unit. The unit name is shown in the Daikin Controller app.

Names are transformed to lowercase. For instance, if the unit name is "DaikinAP44822", the <unit> part of the corresponding data points will be "daikinap44822".

ID	Value	R/W	Description
<unit>.connection	online	R	connection established to the unit
	offline	R	HSYCO can’t connect to the unit (after initial successful discovery)
<unit>.address	<a.b.c.d>	R	the IP address of the unit connected to the local WiFi network. As the address is assigned by the DHCP server, the unit address may change over time
<unit>.fan.direction	off	R	fan blades stay in a fixed position
		W	stop vertical/horizontal movement of fan blades
	h	R	fan blades swing horizontally
		W	enable fan blades horizontal swing
	v	R	fan blades swing vertically
		W	enable fan blades vertical swing
	hv	R	fan blades swing horizontally and vertically
		W	enable fan blades horizontal and vertical swing
<unit>.fan.rate	auto	R	airflow rate automatic operation
		W	set automatic airflow rate
	silence	R	airflow rate quiet operation (reduced flow rate, for low noise operation)
		W	set airflow rate quiet operation
	1 ... 5	R	airflow rate level
		W	set airflow rate level (1 is slower, 5 is faster)
<unit>.humidity.current	<value>	R	the current relative humidity level (if supported by the unit and operation mode)
<unit>.humidity.setpoint	<value>	R	the relative humidity set-point
		W	set the relative humidity set-point (if supported by the unit and operation mode)
	up	W	increase the relative humidity set-point by 10%
	down	W	decrease the relative humidity set-point by 10%
<unit>.mac	<a.b.c.d.e.f>	R	the network interface hardware address of the unit connected to the local WiFi network. The hardware address is fixed
<unit>.mode	auto	R	automatic operation mode
		W	set automatic operation mode (the unit automatically switches between cooling and heating)
	cooling	R	cooling operation mode
		W	set cooling operation mode
	heating	R	heating operation mode
		W	set heating operation mode
	dehum	R	drying operation mode
		W	set drying operation mode (the unit controls the humidity, not the temperature)
	fan	R	fan operation mode
		W	set fan operation mode (temperature control disabled)
<unit>.name	<name>	R	the unit name, as shown in the Daikin Controller app
<unit>.power	off	R	the unit is not operating
		W	turn the unit off
	on	R	the unit is operating
		W	turn the unit on
	flip	W	turn the unit on if currently off, and off if currently on
<unit>.temp.current	<value>	R	the current room temperature (in °C)
<unit>.temp.outside	<value>	R	the current outside temperature (in °C)
<unit>.temp.setpoint	<value>	R	the temperature set-point (in °C)
		W	set the temperature set-point (in °C, with .5 degrees accuracy)
	up	W	increase the temperature set-point by 0.5°C
	down	W	decrease the temperature set-point by 0.5°C
<unit>.version	<value>	R	the unit firmware version

User Interface

Daikinrc Object

The user interface for the DAIKINRC I/O Server.

The daikinrc object is listed in the Project Editor’s new object list only when a DAIKINRC I/O Server is defined.

Parameters

• id: the object's ID, used by UISets
• server id: the server ID.
• unit: the room air conditioner unit id. Supports Redirect variables
• position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(daikinrc[!<id>] <server id>; <unit>; <position>)

E.g.

(daikinrc d1; daikinap30859; r1c1)

UI Attributes

Common attributes

Name	Value	Description
pos	x<x>y<y>	Position specified as x/y coordinates. E.g. x-5y10
visible	true	Default. Show the object
	false	Hide the object
blink	true | slow	Blink the object at a slow speed
	fast	Blink the object at a fast speed
	false	Stop the blinking
opacity	0.0 ... 1.0	Object opacity from 0 (not visible) to 1 (fully visible)
rotation	0 ... 360	Object rotation in degrees. Images are rotated around the center point, all other objects are rotated around the top left corner

Release Notes

3.8.0

• initial release

---

Daikin is a registered trademarks of Daikin Corp.