Texecom

The Texecom Premier Elite control panels are advanced, multi-area security systems. The integration with HSYCO can be accomplished via RS-232 serial communication or via Ethernet connection.

This I/O Server has been tested with firmware version V3.02.00LS2.

Communication

RS-232 parameters:

Baud rate	19200
Data bits	8
Stop bit	2
Parity	none
Flow control	none

HSYCO Configuration

Add a TEXECOM I/O Server in the I/O Servers section of the Settings and set its parameters:

Communication

• Comm ID: select the comm port the device is connected to.

High Availability

• Shutdown when inactive: defaults to true.

Options

ID	Default	Values	Description
startupevents	false	true	generate IO events also during the driver’s start-up phase
		false	start generating events only after HSYCO is aligned with the current status of the system
logsize	20	n ≥ 0	the number of log lines to display in the UI object
pollinterval	3	n > 0	the data acquisition interval, in seconds
maxzone	256	n > 0	highest zone number among the ones used on the panel
maxpartition	16	n > 0	highest partition number among the ones used on the panel
pinlength	4	n > 0	length of the user pins

Datapoints

ID	Value	R/W	Description
connection	online	R	connection established
	offline	R	HSYCO can't connect to the panel
armed	0	R	all areas are disarmed
	1	R	at least one area is armed
a<n>.armed	0	R	area <n> is disarmed
		W	disarm area <n>
	away	R	area <n> is armed in “away” mode
		W	arm area <n> in “away” mode
	stay	R	area <n> is armed in “stay” mode
		W	arm area <n> in “stay” mode
	inst	R	area <n> is armed in “instantaneous” mode
		W	arm area <n> in “instantaneous” mode
a<n>.alarm	0	R	no active alarm on area <n>
	1	R	alarm on area <n>
a<n>.tamper	0	R	no tamper alarm on area <n>
	1	R	tamper alarm on area <n>
a<n>.alarm.mem	0	R	no alarm in memory for area <n>
	1	R	alarm in memory for area <n>
a<n>.tamper.mem	0	R	no tamper alarm in memory for area <n>
	1	R	tamper alarm in memory for area <n>
a<n>.auto	0	R	auto-arming disabled on area <n>
	1	R	auto-arming enabled on area <n>
a<n>.reset	1	W	reset alarms on area <n>
z<n>.state z<n>d.state	closed	R	zone <n> (base or double) is closed
	open	R	zone <n> (base or double) is open
	tamper	R	zone <n> (base or double) is tampered
	short	R	zone <n> (base or double) is in short circuit
z<n>.bypassed z<n>d.bypassed	0	R	zone <n> is not bypassed
		W	unbypass zone <n>
	1	R	zone <n> is bypassed
		W	bypass zone <n>
z<n>.test z<n>d.test	0	R	zone <n> is not in test
	1	R	zone <n> is being tested
z<n>.alarm.mem z<n>d.alarm.mem	0	R	no alarm in memory for zone <n>
	1	R	alarm in memory for zone <n>
z<n>.tamper.mem z<n>d.tamper.mem	0	R	no terminal tamper alarm in memory for zone <n>
	1	R	terminal tamper alarm in memory for zone <n>
or	0	R	the relay output on the panel is not active
		W	deactivate the relay output on the panel
	1	R	the relay output on the panel is active
		W	activate the relay output on the panel
oc1	0	R	the open collector 1 on the panel is not active
		W	deactivate the open collector 1 on the panel
	1	R	the open collector 1 on the panel is active
		W	activate the open collector 1 on the panel
oc2	0	R	the open collector 2 on the panel is not active
		W	deactivate the open collector 2 on the panel
	1	R	the open collector 2 on the panel is active
		W	activate the open collector 2 on the panel
o<n> (if defined in hesa.ini)	0	R	output <n> is not active
		W	deactivate output <n>
	1	R	output <n> is active
		W	activate output <n>
fault.fuse.zones	0	R	zones fuse OK
	1	R	fault on zones fuse
fault.fuse.ibus	0	R	IBUS fuse OK
	1	R	fault on IBUS fuse
fault.battery	0	R	battery OK
	1	R	fault on battery
fault.mains	0	R	mains OK
	1	R	panel mains fault
fault.phone	0	R	phone line OK
	1	R	fault on phone line
fault.jamming	0	R	no jamming
	1	R	radio jamming
fault.radio.battery	0	R	radio zones battery OK
	1	R	low battery on radio zone(s)
fault.radio.loss	0	R	radio zones OK
	1	R	loss of radio zone(s)
battery.volts	<val>	R	the voltage value of the battery is <val> Volts
tamper.panel	0	R	panel OK
	1	R	panel tampered
tamper.cover	0	R	panel cover OK
	1	R	panel cover tampered
tamper.reader	0	R	readers OK
	1	R	reader(s) tampered
tamper.keypad	0	R	keypads OK
	1	R	keypad(s) tampered
tamper.expander	0	R	FLEX5 expanders OK
	1	R	FLEX5 expander(s) tampered
reset	0	R	communication BUS ready
	1	R	ongoing reset procedure on communication BUS
internet	0	R	“internet access” option disabled
	1	R	“internet access” option enabled
service	0	R	service jumper in “RUN” position
	1	R	service jumper in “SERV” position (maintenance)
program	0	R	panel not in programming mode
	1	R	ongoing programming via keyboard
voice	0	R	no SmartLogos30M voice card detected
	1	R	SmartLogos30M voice card detected

User Interface

Hesa Object

The user interface for the control and supervision of one area of the system, the zones and the visualization of the security log:

The Hesa object is listed in the Project Editor’s new object list only when at least one HESA I/O Server is defined.

Parameters

• id - the id assigned to the HESA I/O Server in hsyco.ini. Supports Redirect variables
• area - the number of the area to be addressed. Supports Redirect variables
• pos - the object’s position. Use the pixels or rows and columns coordinates format.

Syntax

(hesa <server id>; <area>; <position>)

E.g.

(hesa serverid; area; x10y20)

UISET Actions

ID	Attribute	Set to
log	value	latest security log lines (as many as specified by the 'logsize' option)
connection.online	visible	true	when datapoint connection = online
		false	when datapoint connection = offline
connection.offline	visible	true	when datapoint connection = offline
		false	when datapoint connection = online
<datapoint_id>.1	visible	true	when datapoint with ID <datapoint_id> has value '1'
		false	when datapoint with ID <datapoint_id> has value '0'
<datapoint_id>.0	visible	true	when datapoint with ID <datapoint_id> has value '0'
		false	when datapoint with ID <datapoint_id> has value '1'

USER Commands

Name	Param	Action
a<n>.armed	0	disarm area <n>
	stay	arm area <n> in "stay" mode
	away	arm area <n> in "away" mode
	inst	arm area <n> in "instantaneous" mode
a<n>.reset	1	reset alarms on area <n>
z<n>.bypassed z<n>d.bypassed	0	unbypass zone <n> (base or double)
	1	bypass zone <n> (base or double)
or	0	deactivate the relay output on the panel
	1	activate the relay output on the panel
oc1	0	deactivate the open collector 1 on the panel
	1	activate the open collector 1 on the panel
oc2	0	deactivate the open collector 2 on the panel
	1	activate the open collector 2 on the panel
o<n>	0	deactivate output <n>
	1	activate output <n>

To perform any of the above operations it is necessary to enter the user code first. To enter the user code through the user interface use user buttons to create a virtual keypad and assign them name and param values according to this table:

Name	Param	Action
digit	{0 ... 9}	append the specified digit to the entered user code
	c	delete the last entered digit

To visualize the number of entered digits use up to 6 text objects (depending on the number of digits used for user codes) and set their IDs to:

ID	Description
pin.<n> (0 ≤ <n> ≤ 5)	shows the character '*' when the corresponding digit has been entered, shows '_' otherwise

The entered code will be cleared after a short period of inactivity.

Log Files

A permanent detailed record of all the Hesa log messages is saved in a file called security.log in the logs/YYYY directory for the current year. This file is never overwritten or deleted by HSYCO.

Other information related to the TEXECOM I/O Server are saved in the daily message.log files.

Release Notes

3.6.0

• initial release

---

Texecom is a registered trademark of Texecom Ltd.