Difference between revisions of "LoRaWAN Utility"
(Created page with "Category:Manager class=appIcon The LoRaWAN Utility application provides a graphical interface to configure a LoRaWAN | LoRaWAN ...") |
|||
| Line 13: | Line 13: | ||
[[File:LoRaWAN_Util_gw_discovery.png|border|600px|center|Gateways discovery]] | [[File:LoRaWAN_Util_gw_discovery.png|border|600px|center|Gateways discovery]] | ||
| + | From the list, click on each gateway to add, edit and save its configuration. | ||
| + | |||
| + | [[File:LoRaWAN_Util_gw_config.png|thumb|250px|Gateway configuration]] | ||
| + | |||
| + | '''Parameters''': | ||
| + | |||
| + | *'''ID''': the ID to assign to the related datapoints of the LoRaWAN I/O Server (i.e. "gw.<id>.*") | ||
| + | *'''MAC''': MAC address of the gateway | ||
| + | *'''IP''': IP address of the gateway | ||
| + | |||
| + | If both MAC and IP are specified, packets received by HSYCO will be considered from this gateway only if both parameters are matching. It is possible to omit (leave blank) MAC '''or''' IP, in which case the packets will be filtered only by the specified parameter. E.g. if only MAC is specified, received packets containing the same MAC address will be assigned to this gateway regardless of the IP address they were sent from. This configuration can be useful when, for instance, the gateway is configured with DHCP and the IP address is dynamic. | ||
| + | |||
| + | After saving the configuration the gateway will no longer be greyed-out in the list: | ||
| + | |||
| + | [[File:LoRaWAN_Util_gw_added.png|border|600px|center|Gateway added]] | ||
| + | |||
| + | To manually add a gateway click on the "+" button at the bottom-left corner of the page. | ||
| + | |||
| + | To remove a gateway, click on it from the list, click on "Delete" and confirm. If the auto-discovery is enabled, the gateway will reappear upon the next received packet from it. | ||
| + | |||
| + | Disable the auto-discovery when all the required gateways have been configured. | ||
| + | |||
| + | The gateways list shows the following fields: | ||
| + | * '''ID''': ID of the gateway | ||
| + | * '''Last seen''': date and time of the last received packet | ||
| + | * '''Gateway time''': internal system time sent by the gateway in the latest status message | ||
| + | * '''ACK rate''': percentage of upstream packets that were acknowledged by HSYCO, as reported in the latest status message from the gateway. If, after initial setup, the value often diverges from 100% there might be networking issues | ||
== Devices == | == Devices == | ||
Revision as of 17:44, 26 April 2019
The LoRaWAN Utility application provides a graphical interface to configure a LoRaWAN I/O Server. When a LoRaWAN I/O Server is defined in HSYCO, the LoRaWAN Utility will appear among the applications of the manager.
Gateways
The LoRaWAN gateway(s) that will be used need to be configured to forward the received device data frames to HSYCO.
To this end, configure the gateway(s) as standard Semtech packet forwarder(s). Make sure the network configuration allows for the communication with HSYCO and use HSYCO's IP address and the port number specified in the "localport" option for the network server's configuration.
When the gateways are correctly configured, make sure the "Auto-discovery" checkbox is enabled under the "Gateways" tab and you will see them appearing in the list:
From the list, click on each gateway to add, edit and save its configuration.
Parameters:
- ID: the ID to assign to the related datapoints of the LoRaWAN I/O Server (i.e. "gw.<id>.*")
- MAC: MAC address of the gateway
- IP: IP address of the gateway
If both MAC and IP are specified, packets received by HSYCO will be considered from this gateway only if both parameters are matching. It is possible to omit (leave blank) MAC or IP, in which case the packets will be filtered only by the specified parameter. E.g. if only MAC is specified, received packets containing the same MAC address will be assigned to this gateway regardless of the IP address they were sent from. This configuration can be useful when, for instance, the gateway is configured with DHCP and the IP address is dynamic.
After saving the configuration the gateway will no longer be greyed-out in the list:
To manually add a gateway click on the "+" button at the bottom-left corner of the page.
To remove a gateway, click on it from the list, click on "Delete" and confirm. If the auto-discovery is enabled, the gateway will reappear upon the next received packet from it.
Disable the auto-discovery when all the required gateways have been configured.
The gateways list shows the following fields:
- ID: ID of the gateway
- Last seen: date and time of the last received packet
- Gateway time: internal system time sent by the gateway in the latest status message
- ACK rate: percentage of upstream packets that were acknowledged by HSYCO, as reported in the latest status message from the gateway. If, after initial setup, the value often diverges from 100% there might be networking issues
