Inim SmartLiving panels are multi-area intrusion detection systems. The integration with HSYCO can be accomplished via direct control through the RS-232 port on the board.
Communication
Employ a female-female RS-232 crossed cable to connect the panel directly to HSYCO or to an Ethernet/RS-232 gateway.
RS-232 parameters:
| Baud rate
|
57600
|
| Data bits
|
8
|
| Stop bit
|
1
|
| Parity
|
none
|
| Flow control
|
none
|
HSYCO Configuration
Options
| ID
|
Default
|
Values
|
Description
|
| gui
|
true
|
true
|
enable support for the UI object, UISET actions and USER commands
|
| false
|
disable UI support
|
| startupevents
|
false
|
true
|
generate IO events also during the driver’s start-up phase
|
| false
|
start generating events only after HSYCO is aligned with the current status of the system
|
| logsize
|
50
|
n ≥ 0
|
the number of log lines to display in the UI object
|
| pollinterval
|
4
|
n > 0
|
the data acquisition interval, in seconds
|
| mod
|
|
515
|
the panel model to control. This option is required
|
| 1050
|
| 10100
|
inim.ini
The guardall.ini file is a specific configuration file located in the root directory.
Here you can define the names of the groups so that they will be automatically added to the user interface. Add a new line for each group using this format:
<io_server_id>.group.<n> = <name>
For instance:
guard.group.1 = Kitchen
guard.group.2 = Living room
Datapoints
| ID
|
Value
|
R/W
|
Description
|
| connection
|
online
|
R
|
connection established
|
| offline
|
R
|
HSYCO can't connect to the panel
|
| armed
|
0
|
R
|
all groups are disarmed
|
| W
|
disarm all groups
|
| 1
|
R
|
the system is (partially) armed
|
| W
|
arm all groups
|
| alarm
|
0
|
R
|
the system is not in a alarm state
|
| 1
|
R
|
the system is in a alarm state
|
| tamper
|
0
|
R
|
the system is not in a tamper state
|
| 1
|
R
|
the system is in a tamper state
|
| panel.tamper
|
0
|
R
|
the panel is not tampered
|
| 1
|
R
|
the panel is tampered
|
| bell.tamper
|
0
|
R
|
the bell is not tampered
|
| 1
|
R
|
the bell is tampered
|
| low.volts
|
0
|
R
|
voltage ok
|
| 1
|
R
|
low voltage detected
|
| sounder
|
0
|
R
|
the sounder is inactive
|
| 1
|
R
|
the sounder is active
|
| audio
|
0
|
R
|
the audio signal of the panel is inactive
|
| 1
|
R
|
the audio signal of the panel is active
|
| strobe
|
0
|
R
|
the strobe is inactive
|
| 1
|
R
|
the strobe is active
|
| mains.fail
|
0
|
R
|
no mains fail
|
| 1
|
R
|
mains fail
|
| power.fail
|
0
|
R
|
no power fail
|
| 1
|
R
|
power fail
|
| battery.fail
|
0
|
R
|
no battery fail
|
| 1
|
R
|
battery fail
|
| fuse.1.fault
|
0
|
R
|
fuse 1 is working
|
| 1
|
R
|
fuse 1 in fault
|
| fuse.2.fault
|
0
|
R
|
fuse 2 is working
|
| 1
|
R
|
fuse 2 in fault
|
| fuse.3.fault
|
0
|
R
|
fuse 3 is working
|
| 1
|
R
|
fuse 3 in fault
|
| line.fault
|
0
|
R
|
communication line is working
|
| 1
|
R
|
communication line in fault
|
| c<n>.name
|
<text>
|
R
|
the name of circuit <n> is set to <text>
|
| g<n>.name
|
<text>
|
R
|
the name of group <n> is set to <text>
|
| g<n>.armed
|
0
|
R
|
group <n> is disarmed
|
| W
|
disarm group <n>
|
| 1
|
R
|
group <n> is armed
|
| W
|
arm group <n>
|
| c<n>.alarm
|
0
|
R
|
circuit <n> is not in alarm state
|
| 1
|
R
|
circuit <n> is in alarm state
|
| c<n>.tamper.alarm
|
0
|
R
|
circuit <n> is not in tamper alarm
|
| 1
|
R
|
circuit <n> is in tamper alarm
|
| c<n>.open
|
0
|
R
|
circuit <n> is closed
|
| 1
|
R
|
circuit <n> is open
|
| c<n>.tamper
|
0
|
R
|
circuit <n> is not tampered
|
| 1
|
R
|
circuit <n> is tampered
|
| c<n>.fault
|
0
|
R
|
circuit <n> is working properly
|
| 1
|
R
|
circuit <n> is faulty
|
| c<n>.bypassed
|
0
|
R
|
circuit <n> is not bypassed
|
| W
|
unbypass circuit <n>
|
| 1
|
R
|
circuit <n> is bypassed
|
| W
|
bypass circuit <n>
|
| c<n>.isolated
|
0
|
R
|
circuit <n> is not isolated
|
| W
|
un-isolate circuit <n>
|
| 1
|
R
|
circuit <n> is isolated
|
| W
|
isolate circuit <n>
|
| c<n>.soaked
|
0
|
R
|
circuit <n> is not soaked
|
| W
|
un-soak circuit <n>
|
| 1
|
R
|
circuit <n> is soaked
|
| W
|
soak circuit <n>
|
| c<n>.status
|
<status_values>
|
R
|
the status of circuit <n> is set to the reported values
|
| c<n>.attributes
|
<attributes_values>
|
R
|
the attributes of circuit <n> are set to the reported values
|
| c<n>.resistance
|
<value>
|
R
|
the measured resistance on circuit <n> is <value> ohm
|
| >20k
|
R
|
the measured resistance on circuit <n> is greater than 20 K-ohm
|
| k<n>.tamper
|
0
|
R
|
keypad <n> is not tampered
|
| 1
|
R
|
keypad <n> is tampered
|
| k<n>.fault
|
0
|
R
|
keypad <n> is working properly
|
| 1
|
R
|
keypad <n> is faulty
|
| logon.<n>
|
<user_num>
|
R
|
user with number <user_num> logged in from keypad <n>
|
| error
|
R
|
wrong pin entered in keypad <n>
|
| system
|
reset
|
W
|
reset alarms
|
| Circuit status values
|
| Value
|
Description
|
| A
|
alarm/open
|
| B
|
alarm/open and tamper
|
| E
|
latched alarm and tamper
|
| M
|
marginal clear
|
| m
|
marginal alarm
|
| N
|
normal
|
| T
|
tamper
|
| L
|
latched alarm
|
| F
|
fault/no answer
|
| X
|
Auxiliary alarm
|
| Circuit attributes values
|
| Value
|
Description
|
| B
|
bypassed circuit
|
| I
|
isolated circuit
|
| S
|
soak failed
|
| T
|
soaked circuit
|
| Y
|
temporarily bypassed circuit
|
| Q
|
temporarily isolated circuit
|
| H
|
circuit in shunt
|
| A
|
existing circuit
|
| M
|
multi-alarm
|
| F
|
bank reset failed/door forced
|
| L
|
locked
|
| O
|
open
|
Attributes can be combined together, for instance if a circuit is both isolated and bypassed, the attribute value will be “BI”.
User Interface
Guardall Object
The user interface for the Guardall multi-area intrusion detection system:
The Guardall object is listed in the Project Editor’s new object list only when at least one Guardall I/O Server is defined.
Parameters
- server id: the server ID. Supports Redirect variables
- position: the object's position. Use the pixels or rows and columns coordinates format
Syntax
(guardall <server id>; <position>)
E.g.
(guardall serverid; x10y20)
UISET Actions
| ID
|
Attribute
|
Set to
|
| log
|
value
|
latest security log lines (as many as specified by the 'logsize' option)
|
| log0
|
value
|
latest line of the security log when a new entry is added, set back to blank after a short period
|
| c<n>.name
|
value
|
name assigned to circuit <n> or its number if no name is defined
|
| connection.label
|
visible
|
true
|
when datapoint connection = offline
|
| false
|
when datapoint connection = online
|
| <datapoint_id>.label.1
|
visible
|
true
|
when datapoint with ID <datapoint_id> has value '1'
|
| false
|
when datapoint with ID <datapoint_id> has value '0'
|
| <datapoint_id>.label.0
|
visible
|
true
|
when datapoint with ID <datapoint_id> has value '0'
|
| false
|
when datapoint with ID <datapoint_id> has value '1'
|
USER Commands
| Name
|
Param
|
Action
|
| armed
|
0
|
disarm all groups
|
| 1
|
arm all groups
|
| g<n>.armed
|
0
|
disarm group <n>
|
| 1
|
arm group <n>
|
| c<n>.bypassed
|
0
|
unbypass zone <n>
|
| 1
|
bypass zone <n>
|
| c<n>.isolated
|
0
|
un-isolate zone <n>
|
| 1
|
isolate zone <n>
|
| c<n>.soaked
|
0
|
un-soak zone <n>
|
| 1
|
soak zone <n>
|
| system
|
reset
|
reset alarms
|
