Ats

Aritech ATS panels are multi-area intrusion detection systems. The integration with HSYCO can be accomplished via direct control through the RS-232 port on the serial module.

Communication

Employ an RS-232 cable to connect the panel directly to HSYCO or to an Ethernet/RS-232 gateway. The cable must follow this pinout diagram:

RS-232 parameters:

Baud rate	same as panel settings (default 4800)
Data bits	8
Stop bit	1
Parity	none
Flow control	RTS/CTS

HSYCO Configuration

Options

ID	Default	Values	Description
gui	true	true	enable support for the UI object, UISET actions and USER commands
		false	disable UI support
startupevents	false	true	generate IO events also during the driver’s start-up phase
		false	start generating events only after HSYCO is aligned with the current status of the system
pollinterval	5	n > 0	the data acquisition interval, in seconds
logsize	20	n ≥ 0	the number of log lines to display in the UI object
maxzone	256	0 ≤ n ≤ 256	highest zone index set on the panel. This option is recommended to improve the I/O Server's performances
maxoutput	256	0 ≤ n ≤ 256	highest output index set on the panel. This option is recommended to improve the I/O Server's performances
maxras	16	0 ≤ n ≤ 16	highest RAS (Remote Arming Station) index set on the panel. This option is recommended to improve the I/O Server's performances

ats.ini

The ats.ini file is a specific configuration file located in the root directory. Here you can define the names of zones and areas so that they will be automatically added to the user interface. Add a new line for each name using this format:

<io_server_id>.zone.<n> = <name>
<io_server_id>.area.<n> = <name>

For instance:

ats.zone.1 = Kitchen
ats.zone.2 = Corridor
ats.area.1 = Floor 1

Datapoints

ID	Value	R/W	Description
connection	online	R	connection established
	offline	R	HSYCO can't connect to the panel
armed	1	R	at least one area is armed
		W	arm all active areas
	0	R	no area is armed
		W	disarm all active areas
alarm	1	R	at least one area is in alarm
	0	R	no area is in alarm
	reset	W	reset system alarms
clock	read	W	request the reading of the panel’s clock value
	<date_time>	R	the panel’s clock is set to <date_time>. The value has the format "yyyy-mm-dd hh:mm:ss" (e.g. "2012-12-30 16:59:23"). This event is only triggered after a request.
a<n>.name	<text>	R	area <n> has been assigned the name <text>
z<n>.name	<text>	R	zone <n> has been assigned the name <text>
a<n>.armed	1	R	area <n> is armed
		W	arm area <n>
	0	R	area <n> is disarmed
		W	disarm area <n>
	force	W	force arm area <n>
a<n>.alarm	1	R	area <n> is in alarm
	0	R	area <n> is not in alarm
a<n>.open	1	R	area <n> has open zones
	0	R	area <n> has no open zones
a<n>.isolated	1	R	area <n> has isolated zones
	0	R	area <n> has no isolated zones
a<n>.exit	1	R	exit time is active on area <n>
	0	R	exit time is not active on area <n>
a<n>.entry	1	R	entry time is active on area <n>
	0	R	entry time is not active on area <n>
a<n>.alarm.local	1	R	local alarms are active on area <n>
	0	R	no local alarm is active on area <n>
a<n>.warning	1	R	console warning is active on area <n>
	0	R	console warning is not active on area <n>
z<n>.state1[Note]	tamper	R	tamper active on zone <n>
	alarm	R	alarm active on zone <n>
	closed	R	zone <n> closed
	night	R	night holdup active on zone <n>
	local	R	local alarm active on zone <n>
	isolated	R	zone <n> isolated
z<n>.state2[Note]	short	R	zone <n> in short circuit
	open	R	zone <n> open
	closed	R	zone <n> closed
	active	R	zone <n> active
	masked	R	zone <n> masked
z<n>.isolated	1	W	isolate zone <n>
	0	W	de-isolate zone <n>
z<n>.alarm	reset	W	reset alarms on zone <n>
o<n>.active	1	R	output <n> is active
		W	activate output <n>
	0	R	output <n> is not active
		W	deactivate output <n>
o<n>.inverted	1	R	output <n> is inverted
	0	R	output <n> is not inverted
ras<n>.offline	1	R	RAS <n> is offline
	0	R	RAS <n> is online
ras<n>.tamper	1	R	RAS <n> is tampered
	0	R	RAS <n> is not tampered
ras<n>.isolated	1	R	RAS <n> is isolated
	0	R	RAS <n> is not isolated
ras<n>.inhibited	1	R	RAS <n> is inhibited
	0	R	RAS <n> is not inhibited
dgp<n>.offline	1	R	DGP <n> is offline
	0	R	DGP <n> is online
dgp<n>.isolated	1	R	DGP <n> is isolated
	0	R	DGP <n> is not isolated
dgp<n>.inhibited	1	R	DGP <n> is inhibited
	0	R	DGP <n> is not inhibited
dgp<n>.battery.missing	1	R	battery missing on DGP <n>
	0	R	battery ok on DGP <n>
dgp<n>.battery.low	1	R	battery low on DGP <n>
	0	R	battery ok on DGP <n>
dgp<n>.battery.test	1	R	battery test active on DGP <n>
	0	R	no battery test active on DGP <n>
dgp<n>.battery.test.fail	1	R	battery test failed on DGP <n>
	0	R	battery test ok on DGP <n>
dgp<n>.mains.fail	1	R	mains failure on DGP <n>
	0	R	mains ok on DGP <n>
dgp<n>.fuse.fail	1	R	fuse failure on DGP <n>
	0	R	fuses ok on DGP <n>
dgp<n>.siren.fail	1	R	siren failure on DGP <n>
	0	R	siren ok on DGP <n>
dgp<n>.tamper	1	R	DGP <n> is tampered
	0	R	DGP <n> is not tampered

Note

The value of a zone status (datapoints z<n>.state1 and z<n>.state2) depends on the configuration of the zone typology.

User Interface

Ats Object

The user interface for the Aritech ATS multi-area intrusion detection system:

The Ats object is listed in the Project Editor’s new object list only when at least one Aritech ATS I/O Server is defined.

Parameters

• server id: the server ID. Supports Redirect variables
• position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(ats <server id>; <position>)

E.g.

(ats serverid; x10y20)

UISET Actions

ID	Attribute	Set to
log	value	latest security log lines (as many as specified by the 'logsize' option)
log0	value	latest line of the security log when a new entry is added, set back to blank after a short period
a<n>.name	value	name assigned to area <n>
z<n>.name	value	name assigned to zone <n>
connection.label	visible	true	when datapoint connection = offline
		false	when datapoint connection = online
<datapoint_id>.label.1	visible	true	when datapoint with ID <datapoint_id> has value '1'
		false	when datapoint with ID <datapoint_id> has value '0'
<datapoint_id>.label.0	visible	true	when datapoint with ID <datapoint_id> has value '0'
		false	when datapoint with ID <datapoint_id> has value '1'

USER Commands

Name	Param	Action
armed	0	disarm all groups
	1	arm all groups