Tridonic

Tridonic is a lighting system based on the DALI bus technology. HSYCO integrates this system and communicates with it through the DALI SCI2 interface module and its communication protocol. The integration relies on a direct connection between the DALI SCI2 interface and HSYCO server’s RS-232 serial port, or through a TCP/IP to serial port gateway.

Communication

The DALI SCI2 interface module communicates with HSYCO through a RS-232 interface.

RS-232 parameters:

Baud rate	38400 bps
Data bits	8
Stop bit	1
Parity	none

Further, the RS-232 signals RTS and DTR must be set to the following levels: RTS = +6 ... +12 V DTR = -6 ... -12 V Refer to the SCI2 manual for installation, wiring and power supply requirements.

Tridonic Configuration

On one BUS, there can be up to 64 dimmers, addressed from 0 to 63, organized in up to 16 groups (0 - 15) or individually addressable. The driver also includes the support for the MSensor 2.0 motion detector and photometer functionalities. The MSensor 2.0 can be configured to work in two different modes:

- Direct-master mode (default mode): The MSensor has a DALI address and sends motion detection and light regulation commands to the group specified by its rotary switch (if the switch is set on the value X the controlled group will be X - 1, if the switch is set on “0” the commands are broadcasted). The light intensity value measured by the light sensor is only read upon request (see I/O Events API)

- Indirect-master mode: The MSensor doesn’t have a DALI address and does not control any dimmer directly. The motion detector and the light sensor have two different eDALI (extended DALI) addresses from which they send motion and light intensity asynchronous events.

HSYCO Configuration

Options

ID	Default	Values	Description
discovery	true	true	auto-detects all DALI devices and groups, and automatically lists them in the systemtopo.txt file
		false	auto-detect for devices is disabled
startupevents	false	true	generate IO events also during the driver’s start-up phase
		false	start generating events only after HSYCO is aligned with the current status of the system
broadcastrange	1...254	<min>-<max>	specifies the minimum <min> and maximum<max> allowed light levels for the broadcast command
groupsrange	g<n>:1...254	g<n>:<min>-<max>	specifies the minimum <min> and maximum<max> allowed light levels for the group <n>. If more than one group range is to be specified, then list the ranges separated by “;”, e.g. groupsrange=g0:20-254;g1:40-250
luxdelta	0	≥ 0	option for MSensors. Specifies the minimum difference between light intensity readings required to generate a new event. I.e. when a “xxx.lux” event is generated, a new event (from the same sensor) will be generated only if the new value is greater than the old value plus the luxdelta value or smaller than the old value minus the luxdelta value

Datapoints

ID	Value	R/W	Description
connection	online	R	connection established
	offline	R	HSYCO can't connect to the panel
<n> g<m> broadcast	on	W	set the light level of the target to the last level set before the off command
	off	R	the target is off
		W	switch the target off
	1...100%	R	the light level of the target corresponds to the reported value
		W	set the light level of the target to the specified value
	X/Y	W	set the light level of the target to the specified fraction (e.g. a value of 1/5 corresponds to 20%)
	min	W	set the light level of the target to the minimum level (1%) without fading
	max	W	set the light level of the target to the maximum level (100%) without fading
	up	W	set the light level of the target one step higher
	down	W	set the light level of the target one step lower
<n>.lux[Note 1]	read	W	request the reading of the light intensity measured by the targeted MSensor
	<lux>	R	the light intensity measured by the targeted MSensor corresponds to the reported value (in lux). The reading must be requested via the “read” function
broadcast.lux[Note 1]	read	W	request the reading of the light intensity on all the MSensors
e<x>.lux[Note 2] where <x> is the eDALI address of the light sensor of the MSensor	<lux>	R	the light intensity measured by the targeted MSensor corresponds to the reported value (in lux)
motion	g<m>[Note 1]	R	a motion event has been reported to group <m>
	broadcast[Note 1]	R	a motion event has been broadcasted
	e<x>[Note 2]	R	a motion event has been generated by the MSensor’s light sensor with eDALI address <x>
<n>.scene g<m>.scene broadcast.scene	0...15	W	set the light level of the target to the value stored for the specified scene number (from 0 to 15)
command	<xxyy>	R	the 2-byte hexadecimal DALI frame[Note 3] has been sent to the system
		W	sends the 2-byte hexadecimal DALI frame[Note 3] to the system
monitor	none	W	none of the DALI frames detected on the bus will be reported
	ignored	W	only the DALI frames detected on the bus not processed by the driver will be reported
	all	W	all the DALI frames detected on the bus will be reported
	<xxyy>	R	the reported 2-byte hexadecimal DALI frame[Note 3] has been detected on the bus
refresh	0	W	the secondary properties of the devices (minimum and maximum levels, fade time and fade rate) won’t be rechecked on every monitor loop iteration
	1	W	the secondary properties of the devices (minimum and maximum levels, fade time and fade rate) will be rechecked on every monitor loop iteration
<n>.error g<m>.error broadcast.error	0	R	the target works properly
	1	R	the target is in an error state

Note 1 

Only available if the MSensor is configured to work in Direct-master mode (default mode).

Note 2 

Only available if the MSensor is configured to work in Indirect-master mode.

Note 3 

The 2-byte DALI frames consist of an 8-bit address part and an 8-bit command part.

The address byte is formatted as follows:

Type of Address	Byte Description
Individual address	0AAAAAAS (AAAAAA = 0 .. 63, S = 0/1)
Group Address	100AAAAS (AAAA = 0 .. 15, S = 0/1)
Broadcast Address	1111111S (S = 0/1)

The command byte is to be interpreted as an arc power level (light intensity) if bit S is 0. The arc power can range between 00 (off) and and FE (maximum level) expressed in hexadecimal. A 1 in the position S means that the command byte is to be interpreted as a DALI command. Refer to the following table for a list of all available commands:

Command	Description
00	Extinguish the lamp without fading
01	Dim up 200 ms using the selected fade rate
02	Dim down 200 ms using the selected fade rate
03	Set the actual arc power level one step higher without fading
04	Set the actual arc power level one step lower without fading
05	Set the actual arc power level to the maximum value
06	Set the actual arc power level to the minimum value
07	Set the actual arc power level one step lower without fading
08	Set the actual arc power level one step higher without fading
10 + scene	Set the light level to the value stored for the selected scene
20	Reset the parameters to default settings
21	Store the current light level in the DTR
2A	Store the value in the DTR as the maximum level
2B	Store the value in the DTR as the minimum level
2C	Store the value in the DTR as the system failure level
2D	Store the value in the DTR as the power on level
2E	Store the value in the DTR as the fade time
2F	Store the value in the DTR as the fade rate
40 + scene	Store the value in the DTR as the selected scene
50 + scene	Remove the selected scene from the slave unit
60 + group	Add the slave unit to the selected group
70 + group	Remove the slave unit from the selected group
80	Store the value in the DTR as a short address
90	Returns the status of the slave as XX
91	Check if the slave is working
92	Check if there is a lamp failure
93	Check if the lamp is operating
94	Check if the slave has received a level out of limit
95	Check if the slave is in reset state
96	Check if the slave is missing a short address
97	Returns the version number as XX
98	Returns the content of the DTR as XX
99	Returns the device type as XX
9A	Returns the physical minimum level as XX
9B	Check if the slave is in power failure mode
A0	Returns the current light level as XX
A1	Returns the maximum allowed light level as XX
A2	Returns the minimum allowed light level as XX
A3	Return the power up level as XX
A4	Returns the system failure level as XX
A5	Returns the fade time as X and the fade rate as Y
B0 + scene	Returns the light level XX for the selected scene
C0	Returns a bit pattern XX indicating which group (0-7) the slave belongs to
C1	Returns a bit pattern XX indicating which group (8-15) the slave belongs to
C2	Returns the high bits of the random address as HH
C3	Return the middle bit of the random address as MM
C4	Returns the lower bits of the random address as LL

Other than the above described commands, it is possible to send the following 2-byte DALI frames:

Frame	Description
A100	All special mode processes shall be terminated	A3XX	Store value XX in the DTR
A5XX	Initialize addressing commands for slaves with address XX
A700	Generate a new random address
A900	Compare the random address with the search address
AB00	Withdraw from the compare process
B1HH	Store value HH as the high bits of the search address
B3MM	Store value MM as the middle bits of the search address
B5LL	Store value LL as the lower bits of the search address
B7XX	Program the selected slave with short address XX
B9XX	Check if the selected slave has short address XX
BB00	The selected slave returns its short address XX
BD00	Go into physical selection mode

The value of the events ID.command and ID.monitor is expressed as a 4-digits string “XXYY” representing the hexadecimal value (upper case letters) of the two bytes. For instance, to send the command 00 to the group 1 of our system “tr”, the following syntax will apply: tr.command = 8300

User Interface

Aton Object

The user interface for the Aton multi-room system:

The Aton object is listed in the Project Editor’s new object list only when at least one Aton I/O Server is defined.

Parameters

• server id: the server ID. Supports Redirect variables
• module: module. Supports Redirect variables
• zone: zone number of the Aton multi-room system (max 12 zones). Supports Redirect variables
• position: the object's position. Use the pixels or rows and columns coordinates format

Syntax

(aton <server id>; <module>; <zone>; <position>)

E.g.

(aton serverid; module; zone; x10y20)

UISET Actions

ID	Attribute	Set to
connection.label.online	visible	true	when datapoint connection = online
		false	when datapoint connection = offline
connection.label.offline	visible	true	when datapoint connection = offline
		false	when datapoint connection = online

USER Commands

To send a user command to the I/O Server just set the name to the ID of a writable (W) datapoint and the parameter to one of the possible values.

For instance, setting the name of a user button to “aton.z1.power” and its param field to “flip”, will result in having a switch for zone 1. Naming it “aton.z1.source” with a valid source as param (e.g. “1”, “2”, or “R1”) will result in a button for setting the audio source of the zone.